PAXXSO1-08 Datasheet, PDF (1/1 Pages) List of Unclassifed Manufacturers – 14-28 pin SO socket/14-28 pin DIP 0.3"or 0.6" plug

PAxxSO1-08(H)-s Data Sheet
14-28 pin SO socket/14-28 pin DIP 0.3"or 0.6" plug
Supported Device/Footprints
This adapter accepts various pin count SO packages with a body
width of 0.3” and lead pitch of 0.050”. The adapter DIP plug has
the same pin count as the SO package. The DIP plug span is
0.3” or 0.6”.
Device Dimensions
This socket can accept devices of the following dimensions:
Body mm (inches)
min.
typ.
max.
7.4
7.8
7.9
(0.291) (0.307) (0.311)
Tip mm (inches)
min.
10.0
(0.394)
typ.
max.
11.6 n/a
(0.457)
Adapter Dimensions
Knee mm (inches)
min. typ.
max.
n/a 9.3
9.4
(0.366) (0.370)
Body Length Lead
Pitch
n/a
1.27
Adapter Construction
The adapter is made up of 2 sub-assemblies. They assemble via
connectors making the adapter modular. This way the sub-
assemblies can be replaced easily
When disassembling the adapter take care not to bend the pins.
When reassembling the adapter note the pin 1 indicators to align
the parts correctly.
The following chart shows the various socket and board part
numbers that make up these adapters.
Adapter
Socket
Board
DIP Plug
PA14SO1-08H-3 14(28H)SD-08 28SO08-14-3
0.3”
PA14SO1-08H-6 14(28H)SD-08 28SO08-14-6
0.6”
PA16SO1-08H-3 16(28H)SD-08 28SO08-16-3
0.3”
PA16SO1-08H-6 16(28H)SD-08 28SO08-16-6
0.6”
PA18SO1-08H-3 18(28H)SD-08 28SO08-18-3
0.3”
PA18SO1-08H-6 18(28H)SD-08 28SO08-18-6
0.6”
PA20SO1-08H-3 20(28H)SD-08 28SO08-20-3
0.3”
PA20SO1-08H-6 20(28H)SD-08 28SO08-20-6
0.6”
PA24SO1-08H-3 24(28H)SD-08 28SO08-24-3
0.3”
PA24SO1-08H-6 24(28H)SD-08 28SO08-24-6
0.6”
PA28SO1-08-3
28SD-08
28SO08-3
0.3”
PA28SO1-08-6
28SD-08
28SO08-6
0.6”
The board is Rev F.
Test Socket
LSC #
xx(28)SD-08
28SD-08
Style
Mfgr/Pn
Lidded ZIF Enplas FP-xx(28H)-1.27-08
Lidded ZIF Enplas FP-28-1.27-08
The xx(28)SD-08 sockets are depopulated from 28 pins to fit the
various devices. The sockets are removable so that they may be
replaced easily. They are depopulated at the Pin 1 end. If you
remove the socket be sure to replace it with the hinge at the Pin
1 end.
These sockets have divider fingers between the contacts. A
device with fewer pins can be properly inserted in a socket with
more pins.
The 28 pin adapter can be used for lower pincount devices. This
feature offers a cost and adapter inventory saving for those that
have the time for more careful device handling.
Wiring
Wiring is 1 to 1. Pin 1 of the SO device is wired to pin 1 of the
DIP plug. Pin 2 to pin 2 and so on around the adapter.
Logical Systems Corporation
PO Box 6184, Syracuse, NY 13217-6184 USA
Tel [phone], FAX [phone]
S Y S T E M S www.logicalsys.com, Email: [e-mail]
PAxxSO1-08(H)-s Data Sheet
Doc: SO108-B.DOC
Rev 6/02/00
Page 1 of 1