LEDDC-60W Datasheet, PDF (1/4 Pages) List of Unclassifed Manufacturers – AC or DC Input Switch Mode LED Drivers

LEDDC-60W Series– Fixed Output & Dimmable
AC or DC Input Switch Mode LED Drivers
Constant Current & Constant Voltage Output with Isolation
Black Magic Thermal Advantage™ Aluminum Housing
Electrical Specifications
Input Voltage Range:
100-277 Vac Nom. (90-305 V Min/Max),
108-250 Vdc
Frequency:
50/60 Hz Nom. (47-63 Hz Min/Max)
Power Factor:
>0.90 @ full load, 100V through 277V
Inrush Current:
<30.0 Amps @ 230 Vac, cold start 25ºC, max load
Input Current:
0.90 Amps max
Maximum Power:
60W
Current Accuracy:
± 2% Over input line variation
Load Regulation:
± 3%
THD:
<_ 20% @ full load
Leakage Current:
400 µA Typical
Hold Up Time:
Half Cycle
Protection:
Output Over-Voltage, Output Over-Current, and
Output Short Circuit Protection reset by power cycling
Environmental Specifications
Minimum Starting Temp: -30ºC
Maximum Case Temp. 90°C
Storage Temperature:
-40ºC to +85ºC
Humidity:
5% to 95%
Cooling:
Convection
Sound Rating:
Class A
Vibration Frequency:
5 to 55 Hz/2g, 30 minutes
Impact Resistance:
1g/s
MTBF:
418,000 Hours at full load and 40ºC ambient conditions
per MIL-217F Notice 2
EMC:
FCC 47CFR Part 15 Class B compliant
• Total Power: 60 Watts
• Input Voltage: 100-277 Vac Nom. or 108-250 Vdc
• UL Dry & Damp Location Rated
• IP66 & NEMA13
• High Power Factor
• UL8750, EN61347, CSA 22.2
• EN61000-3-2, EN61000-3-3 Class C
Ordering Options:
-D: 0-10V & Resistance dimmable version comes with an extra two wires +Purple/-Gray on
the output side. -D 0-10V Dimming is compatible with most quality 0-10V wall dimmers
and direct 0-10V analog signal. See page 3 for additional specifications.
-PD: PWM Dimmable version comes with an extra two wires +Purple/-Gray on the output
side. PD PWM version is PWM Dimmable via a positive 10% to 100% Duty Cycle,
200Hz to 1KHz, 0-10V Pulse. See page 4 for additional specifications.
Constant Current - Product Specifications
Model Number
Output Current Output Voltage Max. Output
(mA ±3%)
Range (Vdc) Power (W)
LEDDC60W-086-C0700-XX
700
28-86
60
Typical
Efficiency
92%
-XX indicates dimming options are available. See options at left. Blank = fixed current output
Constant Voltage - Product Specifications
Model Number
Output Voltage Output Current Max. Output
(Vdc ±5%)
Range (mA) Power (W)
LEDDC60W-086
86
175-700
60
Typical
Efficiency
92%
Sign Components Manual
E332160
Note:
LED drivers are designed and intended to operate LED loads only.
Non-LED loading may be outside the specified design limits of our
LED drivers, and therefore cannot be covered by any warranty.
If you desire to use our LED drivers to operate non-LED loads
please contact us to discuss compatibility.
Specifications subject to change without notice.
Rev 9-2-15
Thomas Research Products • 1225 Bowes Rd • Elgin, IL 60123 • T 847-515-3057 • F 847-515-3047 • www.trpssl.com