|
KZN Datasheet, PDF (1/3 Pages) List of Unclassifed Manufacturers – MINIATURE ALUMINUM ELECTROLYTIC CAPACITORS | |||
|
MINIATURE ALUMINUM ELECTROLYTIC CAPACITORS
Low impedance, 105â
KZNSeries
ã»Adoption of innovative high stability electrolyte
ã»High ripple current and long endurance
ã»Rated voltage range : 6.3 to 100Vdc, Capacitance range : 8.2 to 22,000µF
ã»Endurance with ripple current : 6,000 to 10,000 hours at 105â
ã»Non solvent resistant type
ã»RoHS Compliant
KZN
Higher ripple
KZM P152
âSPECIFICATIONS
Items
Category
Temperature Range
Rated Voltage Range
Capacitance Tolerance
Leakage Current
Dissipation Factor
(tanÐ)
Low Temperature
Characteristics
Endurance
Shelf Life
Characteristics
-40 to +105â
6.3 to 100Vdc
±20% (M)
(at 20â, 120Hz)
I=0.01CV or 3µA, whichever is greater.
Where, I : Max. leakage current (µA), C : Nominal capacitance (µF), V : Rated voltage (V)
(at 20â after 2 minutes)
Rated voltage (Vdc)
6.3V 10V 16V 25V 35V 50V 63V 80V 100V
tanδ (Max.)
0.22 0.19 0.16 0.14 0.12 0.10 0.09 0.09 0.08
When nominal capacitance exceeds 1,000µF, add 0.02 to the value above for each 1,000µF increase.
(at 20â, 120Hz)
Z(-25â)/Z(+20â)
2 max.
Z(-40â)/Z(+20â)
3 max.
(at 120Hz)
The following speciï¬cations shall be satisï¬ed when the capacitors are restored to 20â after subjected to DC voltage with the rated
ripple current is applied (the peak voltage shall not exceed the rated voltage) for the speciï¬ed period of time at 105â.
Case size
Ï5&Ï6.3
Ï8Ã11.5L
Ï10Ã12.5L
Ï8Ã15L, 20L
Ï10Ã16L, 20L, 25L
Ï12.5 to Ï18
Time
6.3Vdc 6,000 hours 8,000 hours 9,000 hours 9,000 hours 10,000 hours
10 to 50Vdc 7,000 hours 9,000 hours 9,000 hours 10,000 hours 10,000 hours
63 to 100Vdc 6,000 hours 8,000 hours 9,000 hours 9,000 hours 10,000 hours
Capacitance change
â¦Â±25% of the initial value (6.3, 10Vdc : â¦Â±30%)
D.F. (tanδ)
â¦200% of the initial speciï¬ed value
Leakage current
â¦The initial speciï¬ed value
The following speciï¬cations shall be satisï¬ed when the capacitors are restored to 20â after exposing them for 500 hours at 105â without
voltage applied. Before the measurement, the capacitor shall be preconditioned by applying voltage according to Item 4.1 of JIS C 5101-4.
Capacitance change
â¦Â±25% of the initial value (6.3, 10Vdc : â¦Â±30%)
D.F. (tanδ)
â¦200% of the initial speciï¬ed value
Leakage current
â¦The initial speciï¬ed value
âDIMENSIONS [mm]
âTerminal Code : E
Sleeve(PET : Brown)
L'
Vent
(Except Ï5 & Ï6.3)
15min.
4min.
(Ï5 to 10)
(Ï12.5 to 18)
Gas escape end seal
âPART NUMBERING SYSTEM
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
E KZN AAA E AA AAA M AAA N
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 100µF:101, 3,900µF:392)
Lead forming·taping code
Terminal code
Voltage code (ex. 16V:160 50V:500)
Series code
Category
Please refer to "Product code guide (radial lead type)"
ÏD 5 6.3 8 10 12.5 16 18
Ïd 0.5 0.5 0.6 0.6 0.6 0.8 0.8
F 2.0 2.5 3.5 5.0 5.0 7.5 7.5
D'
ÏDï¼0.5max.
L'
Lï¼1.5max.
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
149
CAT. No. E1001P
|
▷ |