ISE40-01-62L Datasheet, PDF (1/3 Pages) List of Unclassifed Manufacturers – ZSE40F (Compound pressure)

High Precision Digital Pressure Switch
Specifications
Rated pressure range
Operating pressure range/Set pressure range
Withstand pressure
kPa
ZSE40F (Compound pressure)
ZSE40 (Vacuum pressure)
–100.0 to 100.0kPa
0.0 to –101.3kPa
–100.0 to 100.0kPa
10.0 to –101.3kPa
500kPa
0.1
ISE40 (Positive pressure)
0.000 to 1.000MPa
–0.100 to 1.000MPa
1.5MPa
—
Set pressure
resolution ^{(Note 1)}
MPa
kgf/cmX
bar
psi
mmHg
InHg
—
0.001
0.001
0.02
0.01
1
0.1
0.001
0.01
0.01
0.1
—
—
Applicable fluid
Air, Non-corrosive/Non-flammable gas
Power supply voltage
Current consumption
12 to 24VDC ±10%, Ripple (p–p) 10% or less
55mA or less
Switch output
NPN or PNP 2 outputs
Max. load current : 80mA
Max. applied voltage
: 30VDC (with NPN output)
Residual voltage
: 1V or less (with 80mA load current)
Repeatability
Hysteresis mode
Hysteresis _{Window comparator mode}
±0.2% F.S. ±1digit or less
Variable
Fixed (3 digits) ^Note4)
Response time (with anti-chattering function)
2.5ms or less (with anti-chattering function: 24ms, 192ms and 768ms selections)
Output short circuit protection
Display
Yes
3 1/2 digit LED display (sampling cycle: 5 times/sec.)
Display accuracy
±2% F.S. ±1 digit or less (at ambient temperature of 25 ±3°C)
Operation indicator light
Green LED (OUT1: Lights when ON), Red LED (OUT2: Lights when ON)
Analog output ^{(Note 2)}
Output voltage: 1 to 5V
±5% F.S. or less (in rated pressure range)
Linearity: ±1% F.S. or less
Output impedance: Approx. 1k
Output voltage: 1 to 5V ±2.5% F.S. or less (in rated pressure range)
Linearity: ±1% F.S. or less
Output impedance: Approx. 1k
Auto shift input ^{(Note 3)}
No-voltage input (reed or solid state), input 5ms or more
Environmental
resistance
Enclosure
Ambient temperature range
Ambient humidity range
Withstand voltage
Insulation resistance
IP65
Operating: 0 to 50˚C, Stored: –10 to 60˚C (with no condensation or freezing)
Operating/Stored: 35 to 85% RH (with no condensation)
1000VAC for 1min. between lead wires and body
50M or more (at 500VDC) between lead wires and body
Vibration resistance 10 to 500Hz at the smaller of amplitude 1.5mm or acceleration 98m/sX(10G) in X, Y, Z directions for 2hrs. each (deenergized)
Impact resistance
980m/s^X(100G) in X, Y, Z directions 3 times each (deenergized)
Temperature characteristics
In a temperature range of 0 to 50°C, ±2% F.S. or less of pressure measured at 25°C
Port size
01: R1/8, M5 x 0.8, T1: NPT1/8, M5 x 0.8, W1: Rc1/8
C4: With ø4 One-touch fitting, C6: With ø6 One-touch fitting, M5: M5 female threads
Lead wires
Weight
5 wire oil resistant heavy duty cord (0.15mmX)
01/T1 types approx. 60g, W1 type approx. 80g, C4/C6/M5 types approx. 92g (each including 0.6m lead wires)
Note 1) Equipped with unit switching function
(Types without the unit switching function use SI units (kPa or MPa) only.)
Note
2)
For
ZSE40
(F)/ISE40-m
-
22
62
Note
3)
For
ZSE40
(F)/ISE40-m
-
30
70
Note 4) For ZSE40F (compound pressure) with "psi" indication, this is 0.03 to 0.04 psi.
Note 5) For ZSE40F (compound pressure) with "psi" indication, zero clear is in the
range of ±0.01 psi.
Note:
When equipped with auto shift function, the following ranges can be set.
Set pressure range
–100.0 to 100.0kPa
10.0 to –101.3kPa
– 0.1 to 1.000MPa
Setting range
–100.0 to 100.0kPa
–101.3 to 101.3kPa
–1.000 to 1.000MPa
Internal circuits and wiring examples
ZSE40 (F)
ISE40-m -22 (L)-(M)
With analog output
ZSE40 (F)
ISE40-m -30 (L)-(M)
With auto shift input
1k
1.2k
6.8k
DC (+)
(Brown)
Analog output
(Gray)
OUT1
(Black)
OUT2
(White)
DC (–)
(Blue)
DC (+)
(Brown)
Auto shift input
(Gray)
OUT1
(Black)
OUT2
(White)
DC (–)
(Blue)
12 to 24VDC
ZSE40 (F)
ISE40-m -62 (L)-(M)
With analog output
12 to 24VDC
ZSE40 (F)
ISE40-m -70 (L)-(M)
With auto shift input
1k
1.2k
6.8k
DC (+)
(Brown)
Analog output
(Gray)
OUT1
(Black)
OUT2
(White)
DC (–)
(Blue)
12 to 24VDC
DC (+)
(Brown)
Auto shift input
(Gray)
OUT1
(Black)
OUT2
(White)
DC (–)
(Blue)
12 to 24VDC
1