IPC3SAD Datasheet, PDF (1/6 Pages) List of Unclassifed Manufacturers – Pushbutton switches for harsh environments - bushing Ø 12 mm - momentary

IP series
Pushbutton switches for harsh environments - bushing Ø 12 mm - momentary
Distinctive features and specifications
❑ Illuminated or non-illuminated
❑ Tactile feedback
❑ Wide variety of configurations
❑ Flat round actuator for optional marking
❑ Sealed to IP67
B1
ENVIRONMENTAL SPECIFICATIONS
• Front panel sealing : IP67 according to IEC 60529
IP69K according to DIN 40050-9 (non-illuminated) with cap U5125
• Shock resistance : 100 g according to IEC 512-4, test 6c
• Vibration resistance : 10-500Hz - 10 g according to IEC 512-4, test 6d
• Salt spray : IEC 512-6, test 11f
• Robustness (non-illuminated) : IK06 according to EN 50102 (1 joule)
• Operating temperature : -40°C to +85°C
ELECTRICAL SPECIFICATIONS
• Max. current/voltage rating with resistive load (gold plated silver contacts):
5A 28VDC, 70.000 cycles
0,2A 48VDC, 500.000 cycles
0,5A 48VAC, 500.000 cycles
• Initial contact resistance : 100 mΩ max.
• Insulation resistance : 1 GΩ min. at 500VDC
• Dielectric strength : 1.500 Vrms
• Contact bounce : 10 ms
LED COMPONENT SPECIFICATIONS
LED colour
Super red (L0S)
Yellow (L0Y)
Green (L0G)
Blue (L0B)
White (L0W)
Forward current
20mA
20mA
20mA
20mA
20mA
Typ. forward voltage Max. forward voltage
2,1V
2,3V
2,1V
2,3V
2,1V
2,3V
3,2V
3,8V
3,35V
4,25V
A resistor must be series-connected by the user.
Resistor value = ^{supply voltage - LED forward voltage}
LED forward current
GENERAL SPECIFICATIONS
• Panel thickness : 1,5 mm (.059) min.
4 mm (.157 max.)
• Total travel :
Funct. 3 : 1,7 mm (.067) +/- 0,3 mm
Funct. 5 : 1,3 mm (.051) +/- 0,3 mm
• Typical operating force : 6N +/- 2N
• Low level/mech. life : 1.000.000 cycles
• Torque : 1,5 Nm max. applied to nut
• Soldering : 320°C max. for 3 sec.
MATERIALS
• Case : thermoplastic UL94-V0
• Actuator : polyamide 6/6
• Bushing/bezel : zinc die-cast
(zamac), black painted
• Contacts : silver, gold plated (std)
brass, gold plated (for option 104)
• Multi-wire lead AWG20,
section 0,6 mm²
• LED wire : AWG26, section 0,12 mm²
• Lens : polycarbonate
• Terminal seal : epoxy
AGENCY APPROVAL
2A 125VAC/250VAC
File E83438
Availability : consult factory for
details of approved models.
Marking : to order switches marked
UL, complete ordering format.
Panel cut-out
12.90
(.507)
1
MOUNTING
Matrix mounting
20.00
(.787)
20.00
(.787)
Back of panel space requirement
Ø13.60
(.535DIA)
➀ O-ring
APEM
Ø13.50
(.531DIA)
www.apem.com
B1-15