HS35F-100-R1-SS-12GC Datasheet, PDF (1/3 Pages) List of Unclassifed Manufacturers – HS35 Absolute Encoder

HS35 Absolute Encoder
Built on the same rugged design as the incremental model, the HS35
Absolute Encoder is available with various output options including
Gray Code and Natural Binary. Designed with a cast aluminum hous-
ing, a sealed connector and shaft seals, it carries an IP65 environ-
mental rating. With the optional insulating inserts, it can be mounted
on smaller diameter shafts. It is designed for either a through shaft
mounting or blind shaft mounting with a closed cover to maintain its
environmental rating.
The HS35 Absolute Encoder is avail­a­ ble with the following certification:
EN 55011 and EN 61000-6-2
Electrical Specifications
Options: Parallel: NB or GC 12-14 Bits (see Table 1)
Serial (S3): 12-16 Bits (see Table 3)
Analog: (A1-A5) 12-16 Bits (see Table 2)
Counts Per Shaft Turn: 4096–65536 depending on options
Count Transition Accuracy: ± 1/2 bit maximum (Consult factory over 13 Bits)
Supply Voltage: 5–28 VDC ; 13-28 VDC for Analog
Current Requirements: 120 mA typical
Output Formats: Parallel: Gray Code, Natural Binary, Serial and Analog
Voltage/Output: (see note 2)
28V/V: Line Driver, 5–28 VDC in, Vout = Vin
28V/5: Line Driver, 5–28 VDC in, Vout = 5 VDC
28V/OC: Open Collector, 5–28 VDC in, OCout
SSI: 5–28 VDC in/5Vout (consult factory for more information)
Analog: A1-A5
Protection Level: Reverse, overvoltage and output short circuit protection
Frequency Response: 500kHz or 6000 RPM (Parallel)
Output Termination Pinouts: see tables
For S3 options, reference Spec Addendum 02087-005
For A1-A5 options, reference Spec Addendum 02088-002
Mechanical & Environmental Specs
Shaft Bore: many diameters from .375 to 1.000 inch are available, including metric.
(Consult factory for details)
Allowable Misalignment: 0.005” T.I.R. on mating shaft 0.75” from shaft end
Bore Runout: 0.001 T.I.R. maximum
Starting Torque at 25°C: Through shaft version (SS) = 7 in-oz (max);
Blind shaft version (BS) = 4 in-oz max
Bearings: 52100 SAE High carbon steel
Shaft Material: 416 Stainless Steel
Bearing Housing: Die cast aluminum with protective finish
Cover: Die cast aluminum with protective finish
Bearing Life: 7.5 X 10⁹ revs (50,000 hours @ 2500 RPM)
Maximum RPM: 6,000 mechanical (see frequency response, above)
Moment of Inertia: 0.019 oz-in-sec²
Weight: 18oz typical
Temperature: Operating, 0° to 70°C; Extended temperature ratings are available in the
following ranges: -40 to 70°C, -40
to 85°C. Extended temperature ranges can affect other perfomance factors.
NOTES & TABLES: All notes and tables referred to in the text can be found on pages 2 &3.
HS35 Absolute Encoder Ordering Options for assistance call 800-350-2727
Use this diagram, working from left to right to construct your model number (example: HS35F-100-R1-SS-12GC-28V/V-CW-SM14/19).
All notes and tables referred to can be found on the back of this page.
X=
Express
Encoder
HOUSING :
F = Standard
TYPE:
Shaft Bore:
HS = Hollow Shaft ^{100 = 1.00”}
35 = 3.5” Encoder ^{87 = 0.875”}
Diameter ^{75 = 0.75”}
62 = 0.625”
50 = 0.50” etc
TETHER:
R1 = Tether Block
and Pin
R2 = Tether Arm
SHAFT seal
configuration:
SS = Through Shaft
Rubber Seals
BS = Blind Shaft
Rubber Seal
FS = Through Shaft
Felt Seals
BFS = Blind Shaft Felt
Seal
See note 1
Number
of Bits:
12 = 12 Bits,
Code type:
GC = Gray Code
NB = Natural Binary
*Leave blank for A1-A5
Direction of Count:
CW = Clockwise
increasing count
CCW = Counter clockwise
increasing count
SPECIal
features:
S = Special
features specified on
purchase order
See note 3
4096 counts Voltage/output:
OUTPUT Termination: (consult factory
13 = 13 Bits,
28V/V = 5-28Vin/out
SM14/19 = 19 Pin connector; for more
8192 counts
28V/5 = 5-28Vin/5Vout
SCS = Shielded/Jacketed
information)
14 = 14 Bits,
28V/OC = 5-28Vin/OCout ^{Cable with Cable Seal. Length of Cable is}
16384 counts S3 = SSI
specified in inches (i.e. SCS18 = 18 inches)
15 = 15 Bits, A1 = 4-20mA
SM18 = MS3102R18-1P
32768 Counts A2 = 0-10V
(A1–A5 and S3 outputs only)
16 = 16 Bits, A3 = 0-20mA
(Consult factory for
65536 counts A4 = 0-5V
more information)
A5 = 0-24mA
See note 2
EXPRESS ENCODERS: Items highlighted with
(consult factory for more information)
are standard Express Encoders and ship in one to three days.
BEI and Express Encoder are registered trade-
marks of BEI Sensors and Sytems Company.
Tel: [phone] | Fax: [phone]
7230 Hollister Ave., Goleta, CA 93117-2807 | www.beisensors.com
Specification No. 02070-001 Rev.5-14
These commodities, technology or software if exported from the United States must be in accordance with the Bureau of Industry, and Security, Export Administration regulations. Diversion contrary to U.S law is prohibited.