HS1-1840ARH-Q Datasheet, PDF(1/27 Page) List of Unclassifed Manufacturers – MICROCIRCUIT, DIGITAL-LINEAR, RADIATION HARDENED, SINGLE 16-CHANNEL ANALOG MUX / DEMUX WITH OVERVOLTAGE PROTECTION, MONOLITHIC SILICON

English

English German Russian Spanish Italian Polish Chinese Japanese Korean French Portuguese	Language :

HS1-1840ARH-Q Datasheet, PDF (1/27 Pages) List of Unclassifed Manufacturers – MICROCIRCUIT, DIGITAL-LINEAR, RADIATION HARDENED, SINGLE 16-CHANNEL ANALOG MUX / DEMUX WITH OVERVOLTAGE PROTECTION, MONOLITHIC SILICON

REVISIONS

LTR

DESCRIPTION

DATE (YR-MO-DA)

Add device type 02. Add appendix A for device type 02 only.

Make editorial changes throughout.

Make change to 1.4, 30.2.1, IS(OFF) overvoltage and ID(OFF) overvoltage

tests. - ro

97-04-09

97-09-12

Make change to boilerplate and add device class T for device type 02. - ro

98-12-02

Add level P to table I. Make change to 1.5 and glassivation as specified under

APPENDIX A. - ro

99-04-22

Make change to enable delay waveform as specified on figure 6. - ro

00-04-14

Make changes to supply voltage and VREF to GND limits as specified

under 1.3. Make clarification to paragraphs 4.4.4.2 and 4.4.4.3. - ro

Under 1.5, move footnote 3/ to the latch up parameter. Make correction to the

RL value under the tON(A), tOFF(A) test as specified in table I. - ro

Add a junction temperature limit to paragraph 1.3 and make clarifications to the

figure 3 logic diagram. - ro

Add device type 03. Add paragraphs 2.2, 6.7, and Table IB. Under Table IIB,

delete +IS(OFF), -IS(OFF), -ID(OFF), +ID(OFF), +ID(ON), -ID(ON) parameters.

Under figure A-1, backside metallization, delete the word ânoneâ and replace

with âsiliconâ. Update boilerplate paragraph to current MIL-PRF-38535

requirements. - ro

Add device types 04 and 05. Make changes to paragraphs 1.2.2, 1.3, 1.4, 1.5,

4.4.4.2, A.1.2.2, A.1.2.4, Table IA, Table IB, Table IIA, Table IIB, and figure 1.

Delete paragraph 4.4.4.2.1. - ro

Add case outline Z. Make change to paragraph 3.2.5. Delete figure 4 radiation

exposure circuit. Delete device class M requirements. - ro

Add device types 04 and 05 to Table IIB. Delete LDR, HDR, and EDLRS

references from paragraphs 1.2.2 and A.1.2.2. - ro

Add device type 05 to the Analog input overvoltage range (power on/off)

parameter as specified under paragraph 1.3. - ro

04-06-25

06-02-24

09-06-17

11-01-26

11-06-28

13-05-02

13-07-03

13-08-20

APPROVED

R. MONNIN

J. RODENBECK

C. SAFFLE

REV

SHEET

REV

NNNNNNNNNNN

SHEET

15 16 17 18 19 20 21 22 23 24 25

REV STATUS

REV

NNNNNNNNNNNNN N

OF SHEETS

SHEET

1 2 3 4 5 6 7 8 9 10 11 12 13 14

PMIC N/A

PREPARED BY

RAJESH PITHADIA

STANDARD

MICROCIRCUIT

DRAWING

THIS DRAWING IS AVAILABLE

FOR USE BY ALL

DEPARTMENTS

AND AGENCIES OF THE

DEPARTMENT OF DEFENSE

CHECKED BY

RAJESH PITHADIA

APPROVED BY

MICHAEL FRYE

DRAWING APPROVAL DATE

95-08-23

DLA LAND AND MARITIME

COLUMBUS, OHIO 43218-3990

http://www.landandmaritime.dla.mil

MICROCIRCUIT, DIGITAL-LINEAR, RADIATION

HARDENED, SINGLE 16-CHANNEL ANALOG

MUX / DEMUX WITH OVERVOLTAGE

PROTECTION, MONOLITHIC SILICON

AMSC N/A

DSCC FORM 2233

APR 97

REVISION LEVEL

SIZE

CAGE CODE

67268

SHEET

1 OF 25

5962-95630

5962-E545-13

▷