|
EKMS161VSN471MP25S Datasheet, PDF (1/3 Pages) List of Unclassifed Manufacturers – LARGE CAPACITANCE ALUMINUM ELECTROLYTIC CAPACITORS | |||
|
LARGE CAPACITANCE ALUMINUM ELECTROLYTIC CAPACITORS Downsized snap-ins, 105â
KMSSeries
ã»For solar power generation
ã»Endurance with ripple current : 105â 3,000 hours
ã»Rated voltage range : 160 to 500V
ã»Capacitance range : 47 to 3,300µF
ã»Non solvent resistant type
ã»RoHS Compliant
LXS P267
Longer life
KMS
Downsized
Higher ripple
KMM P252
âSPECIFICATIONS
Items
Category
Temperature Range
Rated Voltage Range
Capacitance Tolerance
Leakage Current
Dissipation Factor
(tanδ)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Endurance
Shelf Life
Characteristics
-25 to +105â
160 to 500Vdc
±20% (M)
(at 20â, 120Hz)
Iâ¦3 CV
Where, I : Max. leakage current (µA), C : Nominal capacitance (µF), V : Rated voltage (V)
(at 20â after 5 minutes)
Rated voltage (Vdc)
160 to 400V
420 to 500V
tanδ (Max.)
0.15
0.20
(at 20â, 120Hz)
Rated voltage (Vdc)
160 to 400V
420 to 500V
Z(-25â)/Z(+20â)
4
8
(at 120Hz)
The following speciï¬cations shall be satisï¬ed when the capacitors are restored to 20â after subjected to DC voltage with the rated
ripple current is applied (the peak voltage shall not exceed the rated voltage) for 3,000 hours at 105â.
Capacitance change
â¦Â±20% of the initial value
D.F. (tanδ)
â¦200% of the initial speciï¬ed value
Leakage current
â¦The initial speciï¬ed value
The following speciï¬cations shall be satisï¬ed when the capacitors are restored to 20â after exposing them for 1,000 hours at 105â without
voltage applied. Before the measurement, the capacitor shall be preconditioned by applying voltage according to Item 4.1 of JIS C 5101-4.
Capacitance change
â¦Â±15% of the initial value
D.F. (tanδ)
â¦150% of the initial speciï¬ed value
Leakage current
â¦The initial speciï¬ed value
âDIMENSIONS [mm]
âTerminal Code : VS (Ï22 to Ï35) : Standard
Sleeve (PET : Brown)
Negative mark
PC board pin-out
(View from Solder side)
10
âTerminal Code : LI (Ï35)
Sleeve (PET : Brown)
Negative mark
PC board pin-out
(View from Solder side)
2-1.2Ã6
Vent
L±2.5
4.0±0.5
2-Ï2
Vent
The standard design has no plastic disc.
âPART NUMBERING SYSTEM
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
E KMS AAA V S N AAA M AAA S
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 100µF:101, 1,000µF:102)
Dummy terminal code
Terminal code (VS, LI)
Voltage code (ex. 160V:161, 400V:401)
Series code
Category
Please refer to "Product code guide (snap-in type)"
L±2.5
4.5±1
5±0.5
14.2±1
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
249
CAT. No. E1001P
|
▷ |