EKMG350ELL102MK20S Datasheet, PDF (1/3 Pages) List of Unclassifed Manufacturers – MINIATURE ALUMINUM ELECTROLYTIC CAPACITORS

MINIATURE ALUMINUM ELECTROLYTIC CAPACITORS
Standard, Downsized, 105ˆ
˔Endurance with ripple current : 1,000 to 2,000 hours at 105ˆ
˔Solvent resistant type except 350 to 450Vdc
(see PRECAUTIONS AND GUIDELINES)
˔RoHS Compliant
KMQ
Downsized
KMG
˗SPECIFICATIONS
Items
Characteristics
Category
Temperature Range ^{-55 to +105ˆ(6.3 to 100Vdc) -40 to +105ˆ(160 to 400Vdc) -25 to +105ˆ(450Vdc)}
Rated Voltage Range
Capacitance Tolerance
Leakage Current
Dissipation Factor
(tanЎ)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Endurance
Shelf Life
6.3 to 450Vdc
ʶ20% (M)
(at 20ˆ, 120Hz)
6.3 to 100Vdc
I=0.03CV or 4ŸA,
whichever
is
greater.
160 to 450Vdc
CV ^{Time After 1minute}
CVʽ1,000 I=0.1CV+40 max.
CV>1,000 I=0.04CV+100 max.
After 5minutes
I=0.03CV+15 max.
I=0.02CV+25 max.
(at 20ˆ after 1 minute)
(at 20ˆ)
Where, I : Max. leakage current (ŸA), C : Nominal capacitance (ŸF), V : Rated voltage (V)
Rated voltage (Vdc)
6.3V 10V 16V 25V 35V 50V 63V 100V 160 to 250V 350 to 400V 450V
tanЎ (Max.)
0.34 0.24 0.20 0.16 0.14 0.12 0.10 0.08 0.20
0.24 0.24
When nominal capacitance exceeds 1,000ŸF, add 0.02 to the value above for each 1,000ŸF increase.
(at 20ˆ, 120Hz)
Rated voltage (Vdc)
6.3V 10V 16V 25V 35V 50V 63V 100V 160 to 250V 350 to 400V 450V
Z(-25ˆ)/Z(+20ˆ)
54322222
3
6
6
Z(-40ˆ)/Z(+20ˆ)
12 10 8 5 4 3 3 3
4
6
-
(at 120Hz)
The following specifications shall be satisfied when the capacitors are restored to 20ˆ after subjected to DC voltage with the rated
ripple current is applied (the peak voltage shall not exceed the rated voltage) for 1,000 hours (2,000 hours to meet the following two conditions
1): 160Vdc and larger, 2) :П12.5 and larger) at 105ˆ.
Capacitance change ʽʶ20% of the initial value
D.F. (tanЎ)
ʽ200% of the initial specified value
Leakage current
ʽThe initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20ˆ after exposing them for 1,000 hours at 105ˆ without
voltage applied. Before the measurement, the capacitor shall be preconditioned by applying voltage according to Item 4.1 of JIS C 5101-4.
Rated voltage
6.3 to 100Vcd
160 to 450Vdc
Capacitance change ʽʶ20% of the initial value
ʽʶ20% of the initial value
D.F. (tanЎ)
Leakage current
ʽ200% of the initial specified value ʽ200% of the initial specified value
ʽThe initial specified value
ʽ500% of the initial specified value
˗DIMENSIONS [mm]

˔Terminal Code : E
Sleeve (PET : Brown)
L'
Vent
(exceptП5)
15min.
4min.
(П5 toП10)
(П12.5 to П18)
Gas escape end seal
ПD 5 6.3 8 10 12.5 16 18
Пd 0.5 0.5 0.6 0.6 0.6 0.8 0.8
F 2.0 2.5 3.5 5.0 5.0 7.5 7.5
ПD'
ПD+0.5max
L'
L+1.5max
˗PART NUMBERING SYSTEM
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
E KMG AAA E AA AAA M AAA N
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 1.0ŸF:1R0,10ŸF:100,100ŸF:101)
Lead forming·taping code
Terminal code
Voltage code (ex. 6.3V:6R3,35V:350,100V:101)
Series code
Category
Please refer to "Product code guide (radial lead type)"
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
(1/3)
CAT. No. E1001L