|
DTL22A Datasheet, PDF (1/4 Pages) List of Unclassifed Manufacturers – Voltage-Controlled, 20 Amp 100 Watt, Electronic Loads | |||
|
NEW
®
®
INNOVATION and EXCELLENCE
DTL Series
DTL22A Model
Voltage-Controlled, 20 Amp
100 Watt, Electronic Loads
Features
â 0-10V input/control voltage
â 0-20A output/load current
â 2.5-50V output compliance voltage
â 0-100W output/load power
â 10M⦠output impedance
â 500Vdc isolation
â ±1% accuracy under all conditions
â 200µsec full-scale step response
â 2" x 2", shielded metal package
â Operate in parallel for higher power
Applications
â Power-supply test and characterization
â Static/dynamic power-supply burn-in
â Power-resistor substitution
â Real-time load simulation
â Capacitor discharge testing
The DTL22A is an isolated (500Vdc), near-ideal (ZIN = ZOUT ⥠10Mâ¦), analog/
voltage-controlled current sink. Its 0-20A output/load current is straightforwardly
"programmed" by applying a 0-10V input. The control signal can be generated by
circuits as simple as the wiper of a trimpot or as sophisticated as programmable logic
controllers (PLCâs) or analog-output computer I/O boards (D/A boards). The DTL22A
supports any combination of IOUT = 0-20 Amps and VOUT = 2.5-50 Volts. Its thermally
efï¬cient, metal package, when properly heat sunk, can dissipate output/load power
up to 100 Watts.
The easy-to-use DTL22A is an excellent building block for low-cost, fully ï¬exible,
power-supply (AC/DC or DC/DC) or power-component (MOSFETâs, diodes, etc.) test
and burn-in applications. It is accurate (±5mA offset error, ±1% overall accuracy),
fast (200µsec full-scale step response), and capable of impressive resolution. If it is
controlled with a 12-bit, 0-10V D/A converter, for example, one LSB (least signiï¬cant
bit) of the D/A corresponds to a 5mA change in the DTL22Aâs output/load current.
The DTL22A is packaged in a small (2" x 2" x 0.5"), thermally efï¬cient metal
package incorporating an aluminum baseplate with threaded inserts. It is powered by
a single +5V supply and draws a mere 150mA.
The DTL22A has an output compliance voltage of 2.5-50 Volts. Should the
output/load voltage drop below the 2.5V required for proper biasing, an internal
monitoring circuit activates the DTL22Aâs output Fault line. See DATELâs DTL22A-LC
for compliance voltages as low as 0.6V.
The DTL22A and other electronic loads, controller boards, and software from
DATEL are outstanding building-block components for power-supply burn-in and test
systems. They are extremely reliable, cost-effective solutions that enable you to
quickly conï¬gure impressively accurate systems.
+5 VOLT
SUPPLY
+5 VOLT
RETURN
ISOLATED
DC/DC
CONVERTER
ISOLATED
DC/DC
CONVERTER
CONTROL
VOLTAGE IN (+)
CONTROL
VOLTAGE IN (â)
FAULT
+
â
BUFFER
AMPLIFIER
AMPLIFIER
CURRENT
DRIVER
ISOLATION
AMPLIFIER
ERROR
DETECTION
Figure 1. Simpliï¬ed Schematic
+LOAD
+LOAD
âLOAD
âLOAD
DATEL, Inc., Mansï¬eld, MA 02048 (USA) · Tel: (508)339-3000, (800)233-2765 Fax: (508)339-6356 · Email: sales@datel.com · Internet: www.datel.com
|
▷ |