CU16025ECPB-W6J Datasheet, PDF (1/1 Pages) List of Unclassifed Manufacturers – 5X7 Dot Character VFD Module

5X7 Dot Character VFD Module
CU16025ECPB-W6J
! 2 X 16 Characters 5mm High
! LCD Compatible Design
! Operating Temp -40°C to +85°C
! Single 5V Supply with Power Save Mode
! High Brightness Blue Green Display
! Selectable 4/8 bit M68/i80 Interface
! ASCII + Extended Character Font
! 8 User Definable Character RAM
! 4 Level Brightness Control Function
1
The module includes the Vacuum Fluorescent Display
glass, driver and micro-controller ICs with refresh RAM,
character generator and interface logic.
The high speed 8 bit parallel interface is 5V CMOS
compatible suitable for connection to a host CPU bus
which can be set to M68 or i80 series interface by a solder
link on the module. Brightness control and power down
functions are provided. A full data sheet is available.
14 x ∅ 1.0
14
11.4 31.0 36.0
12.9
11.82
51.36
75.0
80.0
2.5
2.5
8.10
1.6 5.1
Dimensions in mm & subject to tolerances. Mounting holes 2.5mm dia.
ELECTRICAL SPECIFICATION
Parameter
Symbol Value
Condition
Power Supply Voltage
VCC
5.0VDC +/- 5% GND=0V
Power Supply Current
ICC
150mADC typ. Vcc=5V
Logic High Input
VIH
2.0VDC min.
VCC=5V
Logic Low Input
VIL
0.8VDC max.
VCC=5V
Logic High Output
VOH
Vcc-0.4VDC min. IOH = -1.6mA
Logic Low Output
VOL
0.4VDC max.
IOH =1.6mA
The power on rise time should be less than 50ms.The inrush current at power on can be 2 x ICC.
The Icc current is 10mA maximum while in power down mode.
CHARACTER FONT
OPTICAL and ENVIRONMENTAL SPECIFICATIONS
Parameter
Value
Character Size/Pitch (XxY mm)
2.46 x 4.76/3.26 x 6.01
Dot Size/Pitch (XxY mm)
Luminance
0.38 x 0.56/0.52 x 0.7
700 cd/m² (204 fL) Typ.
Colour of Illumination
Blue-Green (Filter for more colours)
Operating Temperature
-40°C to +85°C
Storage Temperature
-50°C to +85°C
Operating Humidity (non condensing) 20 to 80% RH @ 25°C
SOFTWARE COMMANDS
Instruction
R/W RSD0-D7
Clear Display
L L 01H
Cursor Return Home L L 02H-03H
Entry Mode Set
L L 04H-07H
Display ON/OFF
L L 08H-0FH
Cursor/Display Shift L L 10H-1FH
Function Set
L L 20H-3FH
Brightness Set
L H 00H-03H
Set CG RAM Addr. L L 40H-7FH
Set DD RAM Addr. L L 80H-E7H
Read BUSY/Addr.
H L 00H-FFH
Write Data to RAM
L H 00H-FFH
Read Data from RAM H H 00H-FFH
PIN CONNECTIONS
Pin Sig Pin
1
GND 2
3
(FNC) 4
5
R/W # 6
7
DB0 8
9
DB2 10
11
DB4 12
13
DB6 14
Sig
VCC
RS
E#
DB1
DB3
DB5
DB7
TIMING PARAMETERS (min)
(E)nable Cycle Time 1000ns
(E)nable Pulse Width 450ns
Hold after (E)nable 10ns
JUMPER LINKS
# Interface M68/i80
When jumper link JP2 is
soldered, these inputs
change to i80 series CPU
control lines.
Pin 5= /WR Pin 6 = /RD
Pin 3 (Fnc) Input
This is normally open circuit.
If pads JP1.1 and JP1.2 are
linked. Pin 3 = /Reset.
CONTACT
Noritake Sales Office Tel Nos
Nagoya Japan: [phone]
Canada: [phone]
Chicago USA: [phone]
Munchen (D): [phone]
Itron UK: [phone]
Rest Europe: [phone]
www.noritake-elec.com
Subject to change without notice
NORITAKE ITRON VFD MODULES
2x16, 5mm Dot Character