CONREVSMA014-R178 Datasheet, PDF (1/1 Pages) List of Unclassifed Manufacturers – RP-SMA FEMALE BULKHEAD MOUNT CABLE END CRIMP WITH O-RING FOR RG178 CABLE

Description
Body
Pin
Insulation
O Ring
Washer
Nut
Spacer
Support
Heat Shrink
Material
Brass
BE CU
Teflon
Si Rubber
Brass
Brass
Teflon
Brass
Polyolefin
Finish
Nickel
Gold
Teflon
Rubber
Nickel
Nickel
Teflon
Nickel
Black
1/4"-36UNS-2A
THREADS
SIDE VIEW
FLAT 0.228
(5.80)
RECOMMENDED
MOUNTING HOLE
Ø0.256
(6.50)
0.236
(6.00)
REVISIONS
REV
DESCRIPTION
A Add heat shrink, new frame, revised stripping instruct./dims
PIN
Ø0.020
(0.50)
SPACER
DATE
4/26/10
APPV
CJ
SUPPORT
0.500
(12.70)
Ø0.049
(1.24)
HEAT SHRINK
H0.433
(11.00)
Ø0.236
Ø0.102 ^(6.00)
(2.60)
BACK VIEW
0.787
(20.00)
Ø0.118
(3.00)
0.197
(5.00)
0.417
(10.60)
0.083
(2.10)
0.748
(19.00)
0.248
(6.30)
FLAT 0.228
(5.80)
0.433
(11.00)
WASHER
Ø0.402
(10.20)
NUT
H0.315
(8.00)
1/4-36UNS-2B
THREADS
CONREVSMA014-R178 ASSEMBLY INSTRUCTIONS
1. Strip the cable to the recommended dimensions.
2. Slide the coax into the support until the outside insulation bottoms out
against the inside shoulder of the support.
3. Solder the support onto the braid.
4. Place the spacer onto the center conductor.
5. Solder or crimp the pin onto the center conductor.
6. Insert the pin, center conductor, spacer, and support into the body
until the top of the pin is flush to end of the body.
7. Crimp the tail of the body onto the support with a 0.093” hex crimp tool.
RECOMMENDED CABLE STRIPPING DIMENSIONS
0.217 0.032 0.197
(5.50) (0.80) (5.00)
RG-178 Cable
0.020
(0.50)
0.065
(1.65)
NOTES: (UNLESS OTHERWISE SPECIFIED)
1. ALL DIMENSIONS ARE IN INCHES [mm].
2. DIMENSIONS APPLY AFTER FINISHING.
3. MANUFACTURE TO BE COMPLIANT WITH EU RoHS DIRECTIVE.
4. SAFETY BREAK ALL SHARP CORNERS AND EDGES .02 MAXIMUM.
: THIS DRAWING CONTAINS PROPRIETARY INFORMATION
THAT IS THE SOLE PROPERTY OF CONNECTOR CITY, AND SHALL BE
TREATED AS SUCH. NO DISCLOSURE OR REPRODUCTION OF THIS
159 ORT LANE
MERLIN, OR 97532
DOCUMENT IS PERMITTED, IN WHOLE OR IN PART, WITHOUT THE
EXPRESS WRITTEN PERMISSION OF CONNECTOR CITY OR ITS
DESIGNATED AGENTS.
TITLE:
RP-SMA FEMALE BULKHEAD MOUNT CABLE
MATERIAL:
TOLERANCES:
PROJECTION:
.020 [0.50]-.200 [5.00]= .008 [0.20]
END CRIMP WITH O-RING FOR RG178 CABLE
FINISH:
.200 [5.00]-1.200 [30.00]= .016 [0.40]
1.20 [30.0]-4.75 [120.0]= .024 [0.60]
4.75 [120.0]-12.40 [315.0]= .040 [1.0] ^{ANGLES: 1}
DRAWN: CJ
DT: 4/26/10
SIZE
DWG. NO.
CONREVSMA014-R178
REV
ENGR:
DT:
SCALE: 2:1
DO NOT SCALE DRAWING
SHEET 1 OF 1
LDCFDCC_A