APXK2R5ARA221MF46G Datasheet, PDF (1/2 Pages) List of Unclassifed Manufacturers – Super low ESR, impedance and high heat resistance have been obtained by using conductive polymer as electrolyte.

CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
New!
Surface Mount
@Super low ESR, impedance and high heat resistance have been obtained by using
conductive polymer as electrolyte.
@Rated voltage range : 2.5 to 16Vdc, Capacitance range : 100 to 560MF
@Suitable for DC-DC converters, voltage regulators and decoupling applications used to
computer motherboards etc.
@RoHS Compliant
PXK
Downsized
PXE
?SPECIFICATIONS
Items
Category
Temperature Range ^{-55 to +105C}
Characteristics
Rated Voltage Range
Capacitance Tolerance
Surge Voltage
Leakage Current
Dissipation Factor
(tane)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Endurance
Bias Humidity
Surge Voltage
Failure Rate
2.5 to 16Vdc
P20% (M)
Rated voltageB1.15V
Shall not exceed values shown in STANDARD RATINGS.
(at 20C, 120Hz)
(at 105C)
(at 20C after 2 minutes)
0.12 max.
(at 20C, 120Hz)
Z(-25C)/Z(+20C)[1.15
Z(-55C)/Z(+20C)[1.25
(at 100kHz)
The following specifications shall be satisfied when the capacitors are restored to 20C after the rated voltage is applied for 2,000 hours
(F46 : 1,000 hours) at 105C.
Appearance
No significant damage
Capacitance change [P20% of the initial value
DF (tanE)
[150% of the initial specified value
ESR
[150% of the initial specified value
Leakage current
[The initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20C after subjecting them to the DC rated voltage at
60C, 90 to 95% RH for 1,000 hours (F46 : 500hours).
Appearance
No significant damage
Capacitance change [P20% of the initial value
DF (tanE)
[150% of the initial specified value
ESR
[150% of the initial specified value
Leakage current
[The initial specified value
The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105C for 30 seconds
through a protective resistor(R=1kO) and discharge for 5 minutes 30 seconds.
Appearance
No significant damage
Capacitance change [P20% of the initial value
DF (tanE)
[150% of the initial specified value
ESR
[150% of the initial specified value
Leakage current
[The initial specified value
0.5% per 1,000 hours maximum (Confidence level 60% at 105C)
*Note : If any doubt arises, measure the leakage current after following voltage treatment.
Voltage treatment : DC rated voltage are applied to the capacitors for 120 minutes at 105C.
?DIMENSIONS [mm]
@Terminal Code : A
W
0.3max.
LP0.3 (Note)
Note : L+0.1/-0.2 for F46
AP0.2
Size Code fD L A B C
W
P
E61
5 5.8 5.3 5.3 5.9 0.5 to 0.8 1.4
F46 6.3 4.5 6.6 6.6 7.2 0.5 to 0.8 1.9
F61 6.3 5.8 6.6 6.6 7.2 0.5 to 0.8 1.9
?MARKING
EX) 2.5V330MF
K89A
330
2.5^V
?PART NUMBERING SYSTEM
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
A PXK AAA A RA AAA M AAA G
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 330MF:331, 560MF:561)
Taping code
Terminal code
Voltage code (ex. 2.5V:2R5, 6.3V:6R3)
Series code
Category
Please refer to "Product code guide (conductive polymer type)"
(1/2)
CAT. No. E1001K