APSF160ELL271MHB5S Datasheet, PDF (1/2 Pages) List of Unclassifed Manufacturers – CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS

CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
Radial Lead
14' ^Upgrade!
/1$"1^5. 
4FSJFT
˔Super low ESR, high ripple current capability
˔ESR 5mЊmax. (2 to 4Vdc)
˔Longer life (5,000 hours at 105ˆ)
˔ESR after endurance is specified within the initial spec (2 to 4Vdc)
˔Rated voltage range : 2 to 16Vdc
˔RoHS Compliant
˔Halogen Free
PSF
Lower ESR
PSE
˗SPECIFICATIONS
Items
Characteristics
Category
Temperature Range
-55 to +105ˆ
Rated Voltage Range
Capacitance Tolerance
Surge Voltage
Leakage Current
*Note
Dissipation Factor
(tanЎ)
Low Temperature
Characteristics
(Max.Impedance Ratio)
Endurance
Bias Humidity Test
Surge Voltage Test
Failure Rate
2 to 16Vdc
ʶ20% (M)
Rated voltage(V)Ê·1.15
(at 20ˆ, 120Hz)
(at 105ˆ)
Shall not exceed values shown in STANDARD RATINGS.
(at 20ˆ after 2 minutes)
0.10 max.
(at 20ˆ, 120Hz)
Z(-25ˆ)/Z(+20ˆ)ʽ1.15
Z(-55ˆ)/Z(+20ˆ)ʽ1.25
(at 100kHz)
The following specifications shall be satisfied when the capacitors are restored to 20ˆ after the rated voltage is applied for 5,000 hours
at 105ˆ.
Appearance
No significant damage
Capacitance change ʽʶ20% of the initial value
D.F. (tanЎ)
ʽThe initial specified value
ESR
2 to 4Vdc : ʽThe initial specified value
16Vdc : ʽ150% of the initial specified value
Leakage current
ʽThe initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20ˆ after subjecting them to DC voltage at 60ˆ,
90 to 95% RH for 1,000 hours.
Appearance
No significant damage
Capacitance change ʽʶ20% of the initial value
D.F. (tanЎ)
ʽThe initial specified value
ESR
2 to 4Vdc : ʽThe initial specified value
16Vdc : ʽ150% of the initial specified value
Leakage current
ʽThe initial specified value
The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105ˆ for 30 seconds
through a protective resistor(R=1kЊ) and discharge for 5 minutes 30 seconds.
Appearance
No significant damage
Capacitance change ʽʶ20% of the initial value
D.F. (tanЎ)
ʽThe initial specified value
ESR
2 to 4Vdc : ʽThe initial specified value
16Vdc : ʽ150% of the initial specified value
Leakage current
ʽThe initial specified value
0.5% per 1,000 hours maximum (Confidence level 60% at 105ˆ)
*Note : If any doubt arises, measure the leakage current after the following voltage treatment.
Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105ˆ.
˗DIMENSIONS [mm]
˔Terminal Code : E
F05, F08, H08 ^{Coated Case}
Size code
ПD
Пd
F
ПD'
L'
F05 F08
6.3
0.45 0.6
2.5
L+1.0max.
FA5 H08 HB5 JB5
8.0
10.0
0.5
0.6
3.5
5.0
ПD+0.5max.
L+0.3max. L+1.0max. L+1.5max.
L'
FA5, HB5, JB5 ^{Coated Case}
15min.
4min.
˗MARKING
EX) 2.5V560ŸF
(FA5)
(HB5, JB5)
F ^6D6
560
2.5^V
L'
15min.
4min.
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
(1/2)
CAT. No. E1001M