A121K11CWABP Datasheet, PDF (1/6 Pages) List of Unclassifed Manufacturers – Letter codes G and Q — 6 amp at 125 VAC, 3 amp @ 250 VAC or 6 amp at 28 VDC resistive

MINIATURE SWITCHES
Ordering Table — Standard Toggle Switches
HOW TO ORDER YOUR DESIGN (Bold Face Type indicates items normally in Distributor Stock)
Following the table from left to right, the designer is able to specify
the options wanted. The options are described and illustrated on
pages 24-31. Refer to page 57 for mounting hardware.
To determine a part number select the options desired and fill in
the boxes in the selection guides illustrated below.
Toggle
Switch
Series
Poles
and
Throw
Circuit
Toggle Switch Selection Guide
Lever
Options
Lever
Finish
Bushing
Options
Terminal
Type
Contact
Material
Other
+
+
+
+
+
+
+
+
Poles and Throw
Series _{No. Code}
Circuits
Code
Lever Options and Finishes
Type
Code
Finish
Code
Bushing Options
Type
Code
Terminal Options
Type
Code
Contact Material
Type
Code
Other Option
Type
Code
A SPDT 1
POS. "C"
Lever Lock K1 _{Bright Chrome}
1 Splashproof Lever CW Right Angle PC
Gold/Nickel/Brass B Epoxy Sealed
DPDT 2 ON OFF ON
3PDT 3 ON NONE ON
K Bushing Only
21
.840 Bat
L0
.640 Bat L1
23
.550 Bat
L2
Stain Chrome
Black
2 ^{& Bushing Seal}
3 ^Splashproof
CX
Lever Seal Only
.280 Threaded D
Vertical PC
.100 Spacing
Vertical PC
.150 Spacing
A _{Gold/Nickel/Silver G}
AV
Coin Silver
Q
AV2
K
L
Terminals
Anti-Rotation
Anti-Jam
Bushing
P
4PDT 4 ON NONE ON*
26 ^{Long Mod Cap L3 Black Nylon}
Short Mod Cap L4 Red Nylon
4 _{.280 Smooth}
D9 Printed Circuit
C
5
.350 Flatted
H
Terminals
M
ON* OFF ON* 27
.200 Bat
M White Nylon
6 With Shoulder
Right Angle
R
.840 Flat P1
ON OFF ON* 31
.450 Flat
P3
ON ON ON 32
.250 Flat
P4
.410 Bat
S
ON ON ON* 33 .468 Large
T1
.687 Large
T
.350 Keyway H3
Same Throw
With Shoulder
Right Angle
R2
Locking K1
K ^{Opposite Throw}
Lever Only
PC & Support
15/32 Dia.
T
V30
Splashproof Lever ^TW
15/32 &
PC & Support
V40
NONE ON ON* 34
Panel Seal
PC & Support
15/32 Splashproof TX
V60
ON* ON ON* 35
Lever
PC & Support
Seal Only
V70
NONE ON ON 53
.350 Threaded _Y .750 Wire Wrap W
.437 Threaded Y5 .964 Wire Wrap W1
(With P3 Only)
.425 Wire Wrap W3
.350 Smooth _{Y9 1.062 Wire Wrap W4}
Solder Lugs
Z
Quick Connect Z3
*Momentary Contact
Available on S, M and P3 only.
Add .070 to lever length when using these bushings.
Available with S, M, L0, L1, L2, L3, L4 lever options. Consult factory for availability.
Standard on P1, P3, P4 and K1 lever options. Available on all other levers except T & T1.
These circuits are NOT available with the following 3 and 4 pole options: A, AV, AV2, V30, V40,
V60 and V70.
1 and 2 pole only.
Epoxy seal standard on all terminal options.
Available only with L3 and L4 levers.
Available in 1 pole only.
See page 58 for construction detail, wiring and electrical diagrams.
1, 2 and 3 pole only.
Available on T or T1 lever options only.
Available on T, TW, and TX bushing options. (Bright chrome only.)
Not available on K1 lever.
Same as B, G and Q respectively except terminals brass with tin nickel alloy over nickel plate.
Consult plant for availability.
EXAMPLES:
A232L01YW1B = DPDT toggle switch with an ON-ON-ON circuit, .840" long lever in a bright chrome finish, .350 threaded bushing, .964" long
wire wrap terminals, gold/brass contacts and epoxy sealed terminals.
SPECIFICATIONS:
Contact Ratings —
Letter codes G and Q — 6 amp at 125 VAC, 3 amp @ 250 VAC (U.L.
recognized, CSA certified) or 6 amp at 28 VDC resistive.
Letter codes B and G – 0.5. volt-amp (VA) maximum @ 28 V
maximum (AC or DC).
Life Under Load — 60,000 make-and-break cycles — resistive
load only.
Initial Contact Resistance — 10 milliohms maximum 3 VDC, 100
ma for both silver and gold plated contacts.
Insulation Resistance — 1 & 2 pole —1,000 megohms, min.
3 & 4 pole —1,000 megohms, min.
Dielectric Strength — 1,000 volts rms at sea level.
Bushing Strength — 12 pound-inches without physical damage to
switch.
Weight (including hardware) — SP 0.19 oz.; DP 0.23 oz.; 3-pole
0.28 oz.; 4-pole 0.32 oz.
MATERIALS:
Base (body) — 1- and 2-pole —Diallyl Phthalate (DAP).
3- and 4-pole — high strength phenolic.
Lever (toggle) — Brass, chrome plated.
Flat Lever — Brass, satin chrome finish.
Locking lever cap — Anodized aluminum.
Bushing — Brass, nickel plated.
Clamp (frame) — Stainless steel.
Support brackets — Steel, tin plated.
Switching Contacts and Rockers —
Letter Code B — gold/nickel/brass
Letter Code G — gold/nickel/silver
Letter Code Q — Coin silver
Center Terminal
Letter Codes B, G — Gold flash/nickel/brass
Letter Code Q — Silver plated brass.
Hardware — See page 55-57.
38
Litho in U.S.A GG