48514 Datasheet, PDF (1/1 Pages) List of Unclassifed Manufacturers – RICHMOND 8300, TRANSPARENT STATIC SHIELDING BAG (METAL OUT)

Side Weld Seals 3/8 in.
Item
No.
48500
48501
48502
48503
48504
48505
48506
48507
48508
Size (in.)
Item
WxL
No.
4x4
48509
4x6
48510
5x8
48511
6x8
48512
6 x 10
48513
8x8
48514
8 x 10
48515
8 x 12
48516
10 x 12
Packaged 100 per package
Size (in.)
WxL
10 x 14
11 x 15
12 x 16
12 x 18
14 x 16
14 x 18
14 x 24
18 x 24
© 2012 DESCO INDUSTRIES INC.
Employee Owned
RICHMOND 8300 SERIES
Specifications:
Electrical Properties
Typical Values
Surface Resistance:
  Outer Surface
  Aluminum Layer
<10¹¹ ohms
<10² ohms
  Inner Surface
<10¹¹ ohms
Static Shielding
Charge Generation (nC/in²⁾
<20 nJ
Teflon: -0.03
Quartz: +0.10
Capacitance Probe (to dissipate 1 KV) <30V
Test Procedures/Method
ANSI/ESD S11.11
ANSI/ESD S11.11
ANSI/ESD S11.11
ANSI/ESD S11.31
Modified Incline Plane
Modified Incline Plane
ANSI/EIA 541/Appendix E, 1kV Discharge
Physical Properties:
Bag Thickness:
  Polyester Layer
0.5 Mils Static Dissipative PET film ASTM D-2103   
Aluminum Layer
10-25 Angstroms
  Polyethylene Layer
2.5 Mils Static Dissipative PE film ASTM D-2103
Total Thickness
3.0 to 3.1 Mils
ASTM D-2103
Light Transmission (%)
40% (Tobias)
ASTM D-1003
Seam Strength
Pass
ANSI/ESD S541
Tear Strength (lbs)
>25
ASTM D-1004
Puncture Resistance (lbs)
>10
ASTM D-2065
MVTR (gms / 100 in² / 24 hrs, 100°F) 0.40
ASTM F-1249
Burst Strength (psi)
>50 psi
FTMS 101C, 2065.1
Heat Seal
>10 lbs/in.
375°F, 1/2 sec 60 psi
Abrasion Resistance
>30 cycles
Sutherland Abr. (.0000 Steel Wool)
Outgassing
Pass
ASTM E595
Non-corrosive
Pass
MIL-STD-3010, M3005
Chemical Properties
Corrosion
No effect on aluminum, copper, silver, Sn-Pb coated foil,

stainless steel, low carbon steel
Polycarbonate Capability,
No Amines N-Octanoic Acid
Yes
Not present
High Performance
Static Dissipative
Abrasion Resistant
Coating
Mixed Unsortable Plastic Scrap
7
Mixed unsortable plastic scrap shall contain assorted plastics
of multiple grades that are co-extruded, bonded or laminated
together which are unsortable into individual grades.
Protektive Pak’s bags are recyclable
Aluminum
Shielding Layer
Polyester Layer
Static Dissipative Inner
Polyethylene Layer
A fundamental ESD control principle (see ANSI/ESD S20.20 Foreword):
ESD susceptible items should be transported and stored outside an Electrostatic
protected Area enclosed in low charging, static shielding protective packaging.
The bag’s material meets the performance specification requirements of ANSI/ESD S541.
Made in the
Bag is free of amines, N-octanoic acid, and heavy metals.
United States of America
RICHMOND 8300, TRANSPARENT STATIC SHIELDING BAG (METAL OUT)
PROTEKTIVE PAK
13520 MONTE VISTA AVENUE, CHINO, CA 91710
PHONE [phone], FAX [phone]
www.ProtektivePak.com
DRAWING NUMBER
48500
DATE:
December
2012