1U150 Datasheet, PDF (1/2 Pages) List of Unclassifed Manufacturers – 150W MICRO ATX PC Power with 1U Type

Component Distributors, Inc. ~ www.cdiweb.com ~ [e-mail] ~ 1-800-777-7334
150W MICRO ATX PC Power with 1U Type
1U150 series
Features :
AC input range selected by switch
With +5VSB:0 ~ 1.5A max.
Power good signal output
Power fail signal output
High efficiency
Approvals: UL/ CUL/ CB /CE
Forced air cooling by built-in DC fan
100% full load burn-in test
Low cost
1 year warranty
SPECIFICATION
MODEL
CH1
CH2
CH3
CH4
CH5
STANDBY
DC VOLTAGE
3.3V
5V
12V
-5V
-12V
5VSB
MINIMUM CURRENT
1.2A
2.4A
1.0A
0.1A
0.1A
0A
MAXIMUM CURRENT
6.0A
12A
5.0A
0.5A
0.5A
1.5A
RATED POWER (max.)
150W continue
OUTPUT
RIPPLE & NOISE (max.) Note.2 50mVp-p
100mVp-p
100mVp-p
150mVp-p
150mVp-p
100mVp-p
LINE REGULATION
LOAD REGULATION
HOLD UP TIME
1%
1%
Note.3 5%
5%
16ms min. at full load
1%
2%
2%
1%
10%
10%
10%
4%
VOLTAGE RANGE
90 ~ 132VAC/180 ~ 264VAC selected by switch
FREQUENCY RANGE
47~63Hz
INPUT
EFFICIENCY (Typ.)
AC CURRENT
INRUSH CURRENT (max.)
LEAKAGE CURRENT (max.)
OVER LOAD
70%
5.0A / 115VAC 3.0A / 230VAC
40A / 115VAC 80A / 230VAC
3.5mA / 240VAC
105~150% rated output power
Protection type : Shut down o/p voltage, re-power on to recover
PROTECTION OVER VOLTAGE
SHORT CIRCUIT
+5V, +12V: 110%~130% of rated voltage
Protection type : Shut down o/p voltage, re-power on to recover
All output equipped with short circuit
Protection type : Shut down o/p voltage, re-power on to recover
FUNCTION
POWER GOOD SIGNAL
POWER FAIL SIGNAL
PS-ON INPUT SIGNAL
The TTL compatible signal out with 100ms to 500ms delay after power set up
The TTL compatible signal will go down at least 1ms before +5V below 4.7V
Power on: PS-ON = "Low" or "<0.8V" ; Power off: PS-ON = "Hi" or ">2V"
WORKING TEMP.
WORKING HUMIDITY
ENVIRONMENT STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
-10~+35
20~90% RH non-condensing
-20~+85 , 10~95% RH
0.05% / (0~50 )
10~200Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes
SAFETY STANDARDS
WITHSTAND VOLTAGE
UL1950 Approved
I/P-O/P, I/P-FG:1.5KVAC
SAFETY &
EMC
(Note 4)
ISOLATION RESISTANCE I/P-O/P, I/P-FG:100M Ohms / 500VDC
EMI CONDUCTION & RADIATION Compliance to EN55022 (CISPR22) class B
HARMONIC CURRENT
Compliance to EN61000-3-2,-3
EMS IMMUNITY
Compliance to EN61000-4-2,3,4,5,6,8,11, Light industry level, criteria A
MTBF
100K hrs min. MIL-HDBK-217F (25 )
OTHERS
CONNECTOR
COOLING
DIMENSION
ATX main power connector*1ea Peripheral power connector* 4ea
Forced air ventilation by 4cm DC fan
150*82*42.8mm (L*W*H)
Floppy drive power connector* 1ea
PACKING
0.6kg; 20pcs / 16kg / CARTON
NOTE
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Load regulation is measured from 20% to 100% max. Load.
4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives.
File Name:1U-150-SPEC 2004-06-21
Component Distributors, Inc. ~ www.cdiweb.com ~ [e-mail] ~ 1-800-777-7334