JC050B Datasheet, PDF (9/16 Pages) List of Unclassifed Manufacturers – JC050B

Data Sheet
October 1997
JC050B, JC075B, JC100B Power Modules: dc-dc Converters;
18 Vdc to 36 Vdc Input, 12 Vdc Output; 50 W to 100 W
Feature Descriptions (continued)
Remote On/Off (continued)
Ion/off
+
Von/off
–
ON/OFF
VI(+)
VI(–)
SENSE(+)
VO(+)
VO(–)
SENSE(–)
LOAD
8-720 (C).c
Figure 14. Remote On/Off Implementation
Remote Sense
Remote sense minimizes the effects of distribution
losses by regulating the voltage at the remote-sense
connections. The voltage between the remote-sense
pins and the output terminals must not exceed the out-
put voltage sense range given in the Feature Specifica-
tions table, i.e.:
[VO(+) – VO(–)] – [SENSE(+) – SENSE(–)] ≤ 1.2 V
The voltage between the VO(+) and VO(–) terminals
must not exceed 5.9 V. This limit includes any increase
in voltage due to remote-sense compensation and out-
put voltage set-point adjustment (trim), see Figure 15.
If not using the remote-sense feature to regulate the
output at the point of load, then connect SENSE(+) to
VO(+) and SENSE(-) to VO(-) at the module.
SENSE(+)
SENSE(–)
SUPPLY _II
CONTACT
RESISTANCE
VI(+)
VI(–)
VO(+)
VO(–)
IO
LOAD
CONTACT AND
DISTRIBUTION LOSSES
8-651 (C).h
Figure 15. Effective Circuit Configuration for
Single-Module Remote-Sense Operation
Output Voltage Set-Point Adjustment
(Trim)
Output voltage trim allows the user to increase or
decrease the output voltage set point of a module. This
is accomplished by connecting an external resistor
between the TRIM pin and either the SENSE(+) or
SENSE(–) pins. With an external resistor between the
TRIM and SENSE(–) pins (Radj-down), the output voltage
set point (Vo, adj) decreases (see Figure 16). The follow-
ing equation determines the required external-resistor
value to obtain a percentage output voltage change of
∆%.
Radj-down
=


1----0---0--
∆%
–
2_
kΩ
The test results for this configuration are displayed in
Figure 17. This figure applies to all output voltages.
With an external resistor connected between the TRIM
and SENSE(+) pins (Radj-up), the output voltage set
point (VO, adj) increases (see Figure 18).
The following equation determines the required exter-
nal-resistor value to obtain a percentage output voltage
change of ∆%.
Radj-up
=


V-----O_---(_{---1---0---0-----}+_-----∆_----%------)
1.225∆%
–
(_{---1----0---0---∆--}+_--%---2---∆_----%------)
kΩ
The test results for this configuration are displayed in
Figure 19.
The voltage between the VO(+) and VO(–) terminals
must not exceed 5.9V. This limit includes any increase
in voltage due to remote-sense compensation and out-
put voltage set-point adjustment (trim). See Figure 15.
If not using the trim feature, leave the TRIM pin open.
VI (+)
VO (+)
ON/OFF SENSE(+)
CASE
VI (–)
TRIM
SENSE(–)
Radj-down
RLOAD
VO(–)
8-748 (C).c
Figure 16. Circuit Configuration to Decrease
Output Voltage
Tyco Electronics Corp.
9