CM1581 Datasheet, PDF (4/11 Pages) List of Unclassifed Manufacturers – 5A LOW DROPOUT VOLTAGE REGULATOR

CM1581
5A LOW DROPOUT VOLTAGE REGULATOR
ELECTRICAL CHARACTERISTICS
Electrical Characteristics at IOUT = 0mA, and TJ = +25℃; unless otherwise noted
Parameter
Output Voltage
Output Voltage
Device
CM1581D
CM1581K
CM1581S
CM1581ZJ
CM1581D
CM1581K
CM1581S
CM1581ZJ
Reference Voltage CM1581(adj)
Line Regulator (note 2)
Load Regulation (note 2)
Dropout Voltage (Note 3)
VCONTROL - VOUT
Dropout Voltage (Note 3)
VPOWER - VOUT
Adjust Pin Current
Control Pin Current
Current Limit
Minimum Load Current (Note 4)
Ripple Rejection (Note 5)
Thermal Regulation
Test Conditions
VCONTROL = 3.3V, VPOWER = 2.5V
VCONTROL = 5.0V, VPOWER = 3.3V
VCONTROL = 5.8V, VPOWER = 3.8V
VCONTROL = 7.5V, VPOWER = 5.5V
VCONTROL = 3.3V, VPOWER = 2.5V
VCONTROL = 5.0V, VPOWER = 3.3V
VCONTROL = 5.0V, VPOWER = 4.1V
IOUT = 5A
VCONTROL = 6.5V, VPOWER = 5.8V
VCONTROL = 5.0V, VPOWER = 3.3V (note1)
VCONTROL = (VOUT + 1.5V) to 12V, VPOWER = (VOUT +
0.8V) to 7V, IOUT = 10mA to 5A
1.5V+ VOUT <= VCONTROL <= 12V,
0.8V<= VPOWER - VOUT <= 5.5V
VCONTROL = VOUT + 2.5V, VPOWER = VOUT + 0.8V,
IOUT = 10mA to 5A
VPOWER = VOUT + 0.8V
IOUT = 10mA
IOUT = 5A
VCONTROL = VOUT + 2.5V
IOUT = 10mA
IOUT = 5A
VCONTROL = 2.75V, VPOWER = 2.05V,
IOUT = 10mA
VCONTROL = VOUT + 2.5V, VPOWER = VOUT + 0.8V,
IOUT = 10mA to 5A
(VIN – VOUT ) = 1.5V
VCONTROL = 5.0V, VPOWER = 3.3V
VCONTROL = VPOWER = VOUT + 2.5V,
VRIPPLE = 1VPP, IOUT = 2.5A
TA = 25℃
CM1581
Unit
Min. Typ. Max.
1.792 1.800 1.818 V
2.474 2.500 2.525 V
3.267 3.300 3.333 V
4.950 5.000 5.050 V
1.771 1.800 1.829 V
2.460 2.500 2.540 V
3.247 3.300 3.353 V
4.920 5.000 5.080 V
1.238 1.250 1.262 V
1.230 1.250 1.270 V
0.04 0.20
%
0.08
0.3
%
1.00 1.15
1.15 1.30
V
0.10 0.17
V
0.45 0.50
50
120 µA
80
135 mA
5.1
6.8
5
A
10
mA
60
80
dB
0.003
%/W
Note 1: Output voltage is set to be 2.5V.
Note 2: Line and load regulations are guaranteed up to maximum power dissipation determined by input/output differential and
the output current. However, the maximum power will not be available over the full input/output voltage range.
Note 3: The specifications represent the minimum input/output voltage required to maintain 1% regulation.
Note 4: The minimum load current is the minimum current required to maintain regulation. Normally the current in the resistor
divider used to set the output voltage is selected to meet the minimum load current requirement.
Note 5: These parameters, although guaranteed, are not tested in production prior to shipment.
2002/02/05 Preliminary Rev. 1
Champion Microelectronic Corporation
Page 4