PA241 Datasheet, PDF (2/6 Pages) List of Unclassifed Manufacturers – High Voltage Power Operational Amplifiers

PA241
ABSOLUTE MAXIMUM RATINGS
SPECIFICATIONS
ABSOLUTE MAXIMUM RATINGS
SUPPLY VOLTAGE, +V_S to –V_S
OUTPUT CURRENT, continuous within SOA
OUTPUT CURRENT, peak
POWER DISSIPATION, continuous @ T_C = 25°C
INPUT VOLTAGE, differential
INPUT VOLTAGE, common mode
TEMPERATURE, pin solder – 10 sec
TEMPERATURE, junction²
TEMPERATURE, storage
TEMPERATURE RANGE, powered (case)
SPECIFICATIONS
PARAMETER
TEST CONDITIONS¹
PA241CE, PA241DF
MIN
TYP
MAX
INPUT
OFFSET VOLTAGE, initial
OFFSET VOLTAGE, vs. temperature³
OFFSET VOLTAGE, vs supply
OFFSET VOLTAGE, vs time
BIAS CURRENT, initial⁶
BIAS CURRENT, vs supply
OFFSET CURRENT, initial⁶
INPUT IMPEDANCE, DC
INPUT CAPACITANCE
COMMON MODE, voltage range
COMMON MODE, voltage range
COMMON MODE REJECTION, DC
NOISE, broad band
NOISE, low frequency
Full temperature range
V_CM = ±90V DC
10kHz BW, R_S = 1K
1-10 Hz
+V_S–14
-V_S+12
84
25
100
3
70
5/50
0.2/2
2.5/50
10¹¹
6
94
50
125
40
500
130
50/200
50/200
GAIN
OPEN LOOP at 15Hz
BANDWIDTH, gain bandwidth product
POWER BANDWIDTH
R_L = 5K
280V p-p
90
96
3
30
OUTPUT
VOLTAGE SWING
CURRENT, peak⁴
CURRENT, continuous
SETTLING TIME to .1%
SLEW RATE
RESISTANCE⁵, 1mA
RESISTANCE⁵, 40 mA
POWER SUPPLY
VOLTAGE
CURRENT, quiescent
I_O = 40mA
10V step, A _V = –10
C_C = 3.3pF
R_CL = 0
R_CL = 0
±V_S–12
120
60
±V_S–10
2
30
150
5
±50
±150
2.2
±175
2.5
THERMAL
PA241CE RESISTANCE, AC junction to case F > 60Hz
5.4
6.5
PA241DF RESISTANCE, AC junction to case F > 60Hz
6
7
PA241CE RESISTANCE, DC junction to case F < 60Hz
9
10.4
PA241DF RESISTANCE, DC junction to case F < 60Hz
9
11
PA241CE RESISTANCE, junction to air
Full temperature range
30
PA241DF RESISTANCE, junction to air⁷
Full temperature range
25
TEMPERATURE RANGE, case
Meets full range spec's –25
+85
PA241CE
PA241CEA
350V
60 mA
120 mA
12W
±16 V
±V_S
300°C
150°C
–65 to +150°C
–40 to +125°C
PA241DF
PA241DFA
350V
60 mA
120 mA
12W
±16 V
±V_S
220°C
150°C
–65 to +150°C
–40 to +125°C
PA241CEA
MIN
TYP
MAX
UNITS
15
30
mV
*
*
µV/°C
*
µV/V
*
*
µV/kh
*
*
pA
*
pA/V
*
*
pA
*
*
pF
*
V
*
V
*
*
dB
*
µV RMS
*
µV p-p
*
*
*
*
dB
MHz
kHz
±V_S–10
*
*
±V_S–8.5
*
*
*
*
V
mA
mA
µs
V/µs
Ω
Ω
*
*
*
V
*
2.3
mA
*
*
°C/W
*
*
°C/W
*
*
°C/W
*
*
°C/W
*
°C/W
*
°C/W
*
*
°C
NOTES: *
1.
2.
3.
4.
5.
6.
7.
"A" specification is the same as the non "A" specification.
Unless otherwise noted T_C = 25°C, C_C = 6.8pF. DC input specifications are ± value given. Power supply voltage is typical
rating.
Long term operation at the maximum junction temperature will result in reduced product life. Derate internal power dissipation
to achieve high MTTF. For guidance, refer to heatsink data sheet.
Sample tested by wafer to 95%.
Guaranteed but not tested.
The selected value of R_CL must be added to the values given for total output resistance.
Specifications separated by / indicate values for the PA241CE and PA241DF respectively.
Rating applies with solder connection of heatslug to a minimum 1 square inch foil area of the printed circuit board.
CAUTION
The PA241 is constructed from MOSFET transistors. ESD handling procedures must be observed.
APEX MICROTECHNOLOGY CORPORATION • 5980 NORTH SHANNON ROAD • TUCSON, ARIZONA 85741 • USA • APPLICATIONS HOTLINE: [phone]
2