D221I Datasheet, PDF (2/2 Pages) List of Unclassifed Manufacturers – High Isolation Miniature, 2W SIP DC/DC Converters

Model Selection Guide
Model
Number
D201I
D202I
D203I
D204I
D205I
D206I
D207I
D211I
D212I
D213I
D214I
D215I
D216I
D217I
D221I
D222I
D223I
D224I
D225I
D226I
D227I
D231I
D232I
D233I
D234I
D235I
D236I
D237I
Input
Voltage (VDC)
Current (mA)
Nominal Range Full-Load No-Load
5
4.5 - 5.5
533
35
5
4.5 - 5.5
513
35
5
4.5 - 5.5
495
35
5
4.5 - 5.5
499
35
5
4.5 - 5.5
533
35
5
4.5 - 5.5
504
35
5
4.5 - 5.5
501
35
12 10.8 - 13.2 204
25
12 10.8 - 13.2 212
25
12 10.8 - 13.2 196
25
12 10.8 - 13.2 200
25
12 10.8 - 13.2 216
25
12 10.8 - 13.2 201
25
12 10.8 - 13.2 200
25
24 21.6 - 26.4 92
10
24 21.6 - 26.4 108
10
24 21.6 - 26.4 101
10
24 21.6 - 26.4 101
10
24 21.6 - 26.4 108
10
24 21.6 - 26.4 102
10
24 21.6 - 26.4 99
10
48 42.0 - 52.0 59
10
48 42.0 - 52.0 54
10
48 42.0 - 52.0 51
10
48 42.0 - 52.0 50
10
48 42.0 - 52.0 54
10
48 42.0 - 52.0 51
10
48 42.0 - 52.0 50
10
Voltage
(VDC)
3.3
5.0
12.0
15.0
±5.0
±12.0
±15.0
3.3
5.0
12.0
15.0
±5.0
±12.0
±15.0
3.3
5.0
12.0
15.0
±5.0
±12.0
±15.0
3.3
5.0
12.0
15.0
±5.0
±12.0
±15.0
Output
Current
(mA, Max)
400.0
400.0
165.0
133.0
±200.0
±83.0
±66.0
400.0
400.0
165.0
133.0
±200.0
±83.0
±66.0
400.0
400.0
165.0
133.0
±200.0
±83.0
±66.0
400.0
400.0
165.0
133.0
±200.0
±83.0
±66.0
Current
(mA, Min)
10.0
8.0
3.0
2.5
±4.0
±1.5
±1.0
10.0
8.0
3.0
2.5
±4.0
±1.5
±1.0
10.0
8.0
3.0
2.5
±4.0
±1.5
±1.0
10.0
8.0
3.0
2.5
±4.0
±1.5
±1.0
Load
Regulation
(%, Max)
12
12
8
8
12
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
Efficiency
(%, Typ)
Fuse Rating
Slow-Blow
(mA)
75
1,000
78
1,000
80
1,000
80
1,000
75
1,000
79
1,000
79
1,000
67
500
78
500
85
500
83
500
77
500
82
500
82
500
74
200
77
200
81
200
82
200
77
200
81
200
84
200
70
100
77
100
81
100
82
100
76
100
81
100
82
100
Notes:
1. Output load regulation is specified for a load change of 20% to 100%.
2. When measuring output ripple, it is recommended that an external ceramic capacitor (approx 10 µF)
be placed from the +Vout pin to the -Vout pin for single output units and from each output to common
for dual output units.
3. All 3.3, 5 and ±5 VDC output models may be operated to +85ºC ambient with an unobstructed airflow
of 3.6 ft/S (1.1 m/S).
4. The 5V, 12V and 24V input units do not require external components to operate, but the use of an
input capacitor (10 µF) may enhance performance in some applications. An output capacitor (1.0 µF
to 10 µF) may be used to reduce ripple. The 48V input models require an input capacitor of 4.7 uF to
47 uF (dependent upon the application).
5. Dual output units may be connected to provide a 10V, 24V or 30 VDC output. To do this, connect the
load across the positive (+Vout) and negative (-Vout) outputs and float the output common.
6. It is recommended that a fuse be used on the input of a power supply for protection. See the table above
for the correct rating.
Pin Connections
Pin Single
Dual
1
+Vin
+Vin
2
-Vin
-Vin
5
-Vout
-Vout
6 No Pin Common
7
+Vout +Vout
Mechanical Dimensions
Derating Curve
Capacitive
Load
Single Output
(μF Max)
470
Dual Output
(μF Max)
±390
Notes: All dimensions are typical in inches (mm)
Tolerance x.xx = ±0.01 (±0.25)
Pin 1 is marked by a “dot” or indentation on the side of the unit
MicroPower Direct
www.micropowerdirect.com
232 Tosca Drive Stoughton, MA 02072
■
TEL: [phone]
■
FAX: [phone]
■
E-Mail: [e-mail]