HDC135 Datasheet, PDF (1/2 Pages) List of Unclassifed Manufacturers – High Speed Optocouplers

Product Bulletin HDC135
September 1996
High Speed Optocouplers
Types HDC135, HDC136, HDC135B, HDC136B
Features
• High speed
• TTL compatible
• High common mode transient
immunity
• Wide bandwidth
• Open collector output
Description
Optek’s HDC135 and HDC136 are high
speed optocouplers, consisting of IR
emitters and integrated photodetectors
in hermetic side brazed dual-in-line 8 pin
packages. Electrical characteristics are
similar to the 6N135 and 6N136
optocouplers but with full military
temperature range operation.
The HDC135B and HDC136B are high
reliability optocouplers with 100%
processing and Group Testing patterned
after MIL-STD-883 Method 5004 and
5005 for class B.
Typical screening and lot acceptance
tests are provided on page 13-4.
Absolute Maximum Ratings (No derating required up to 70^o C)
Storage Temperature Range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55^o C to +150^o C
Operating Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55^o C to +125^o C
Lead Soldering Temperature [1/16 inch (1.6 mm) from case for 10 seconds) . 260^o C
Average Input Current - I_F . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 mA⁽¹⁾
Peak Output Current - I_F (50% duty cycle, 1 ms pulse width) . . . . . . . . . . . . 50 mA⁽²⁾
Peak Transient Input Current - I_F (≤1 µs pulse width, 300 pps) . . . . . . . . . . . . . 1.0 A
Reverse Input Voltage - V_R . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.0 V
Input Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 mW⁽³⁾
Average Output Current - I_O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.0 mA
Peak Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.0 mA
Emitter-Base Reverse Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.0 V
Supply and Output Voltage - V_CC, V_O . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 V to 15 V
Base Current - I_B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.0 mA
Output Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 mW⁽⁴⁾
Caution: This component is susceptible to damage from electrostatic discharge. Normal static
prevention procedures should be used in handling.
Notes:
(1) Derate linearly above 70^o C free-air temperature at a rate of 0.45 mA/^o C.
(2) Derate linearly above 70^o C free-air temperature at a rate of 0.9 mA/^o C.
(3) Derate linearly above 70^o C free-air temperature at a rate of 0.8 mW/^o C.
(4) Derate linearly above 70^o C free-air temperature at a rate of 1.8 mW/^o C.
(5) CMH is the maximum allowable dV/dt on the leading edge of a common mode pulse to
assure that the output will not switch from high to low.
(6) CML is the maximum negative dV/dt allowable on the trailing edge of a common mode pulse
to assure that the output will not switch from low to high.
(7) Test conditions represents 1 TTL unit load with 5.6 kΩ pull-up resistor.
(8) Test conditions represents 1 LSTTL unit load with a 6.1 kΩ pull-up resistor.
(9) Device considered a two-terminal device: pins 2 and 3 shorted together and pins 5, 6, 7 and
8 shorted together.
Minimum orders will apply to processed
devices.
Optek Technology, Inc.
1215 W. Crosby Road
Carrollton, Texas 75006
13-22
[phone]
Fax [phone]