DSD2410 Datasheet, PDF (1/2 Pages) List of Unclassifed Manufacturers – Time Delay Relay 10-50 Amp

Series DSD, DLD
Time Delay Relay • 10-50 Amp
• DC Control, AC Output
• External Adjustment
• Industry Standard Package
• Zero Voltage Turn-On
• Panel Mount
These “on-operate” (pull-in) time-delay
solid state relays are housed in a single
industry standard package. AC output
is controlled by a DC input and has an
externally adjustable time delay.
Choices include models with two time-
delay ranges.
Manufactured in Crydom's ISO 9001
Certified facility for optimum product
performance and reliability.
MODEL NUMBERS
OUTPUT SPECIFICATIONS➀
DSD2410
Operating Voltage Range (47-63 Hz) [Vrms]
Load Current Range ➂ [Arms]
Transient Overvoltage [Vpk]
Max. Surge Current, (16.6ms) [Apk]
Max. On-State Voltage Drop @ Rated Current [Vpk]
Thermal Resistance Junction to Case [R_θJC]
Maximum I ² t for Fusing, (8.3 msec.) [A ^2sec]
Max. Off-State Leakage Current @ Rated Voltage [mArms]
Min. Off-State dv/dt @ Max. Rated Voltage [V/µsec] ➁
Max. Turn-On Time ➃
Max. Turn-Off Time
Max. Reset Time [µsec] ➄
Power Factor (Min.) with Max. Load
48-280
.04-10
600
120
1.6
1.48
60
10
500
1/2 cycle
100
0.5
DSD2425 DSD2450 DLD2410
48-280
48-280
48-280
.04-25
.04-50
.04-10
600
600
600
250
625
120
1.6
1.6
1.6
1.02
0.63
1.48
260
1620
60
10
10
10
500
500
500
Adjustable, See Table
1/2 cycle 1/2 cycle 1/2 cycle
100
100
100
0.5
0.5
0.5
DLD2425
48-280
.04-25
600
250
1.6
1.02
260
10
500
1/2 cycle
100
0.5
DLD2450
48-280
.04-50
600
625
1.6
0.63
1620
10
500
1/2 cycle
100
0.5
INPUT SPECIFICATIONS ➀ DC CONTROL
TYPICAL TURN-ON DELAY ➀
Control Voltage Range
Max. Turn-On Voltage
Min. Turn-Off Voltage
Min. Input Impedance
Typical Input Current
3.5-15Vdc
3.5 Vdc
1.0 Vdc
1500 Ohms
3.4mA @ 5 Vdc, 11.4mA @ 15Vdc
RESISTOR
O (Short)
10K Ω
100KΩ
470KΩ
1.0MΩ ➃
TIME (DSD)
0.10 sec
0.19 sec
0.94 sec
4.0 sec
8.3 sec
TIME (DLD)
1.6 sec
3.1 sec
15 sec
64 sec
133 sec
GENERAL NOTES
© 2002 CRYDOM CORP, Specifications subject to change without notice.
➀ All parameters at 25˚C unless otherwise specified.
➁ Off-State dv/dt test method per EIA/NARM standard RS-443, paragraph 13.11.1
➂ Heat sinking required, for derating curves see page 2.
➃ Timing Resistor may be as high as 10M Ohm with performance dependent on resistor quality.
➄ Before and after time-out.
FastFax Document No. 201
DSD,DLD.
Rev.021302
PAGE 1 OF 2
For recommended applications and more information contact:
USA: Sales Support [phone] Tech Support [phone] FAX [phone]
Crydom Corp, 2320 Paseo de las Americas, Ste. 201, San Diego, CA 92154
Email: [e-mail] WEB SITE: http://www.crydom.com
UK: [phone] • FAX [phone] Crydom International Ltd., 7 Cobham
Road, Ferndown Industrial Estate, Ferndown, Dorset BH21 7PE, Email: [e-mail].
GERMANY: [phone]