AZ695 Datasheet, PDF (1/2 Pages) List of Unclassifed Manufacturers – SENSITIVE SUBMINIATURE RELAY

AZ695
SENSITIVE
SUBMINIATURE RELAY
FEATURES
• Extremely small footprint utilizing only 0.18 square
inch of PCB area
• Thin vertical profile only 0.256" wide
• 1 Form A contact with up to 5 Amp switching
capability
• High sensitivity, 100 mW pickup
• Dielectric strength 3000 Vrms contact to coil
• Coils to 24 VDC
• Epoxy sealed for automatic wave soldering
and cleaning
• Sockets are also available
• UL file E44211; CSA file 74461
CONTACTS
GENERAL DATA
Arrangement
Ratings
Material
Resistance
SPST (1 Form A)
Resistive load:
Max. switched power: 150 W or 1250 VA
Max. switched current: 5 A
Max. switched voltage: 150* VDC or 250 VAC
Inductive load (p.f. = 0.40, L/R = 7 ms)
2 A at 250 VAC, 30 VDC
UL Rating: 5 A at 30 VDC or 250 VAC
1_{/10 HP 120 VAC}
Note: If switching voltage is greater than 30 VDC, special
precautions must be taken. Please contact the factory.
Options:
Silver cadmium oxide
Silver cadmium oxide with gold plating
< 30 milliohms initially
(at rated current, voltage drop method)
COIL
Power
At Pickup Voltage
(typical)
Max. Continuous
Dissipation
Temperature Rise
100 mW
550 mW at 20°C (68°F) ambient
420 mW at 40°C (104°F) ambient
25°C (45°F) at nominal coil voltage
Life Expectancy
Mechanical
Electrical
Minimum operations
20 million operations
1 X 10⁵ at 5 A, 30 VDC or 250 VAC
Operate Time (typical) 6 ms at nominal coil voltage
Release Time (typical) 3 ms at nominal coil voltage
(with no coil suppression)
Dielectric Strength
750 Vrms between open contacts
(at sea level for 1 min.) 3000 Vrms contact to coil
Insulation
Resistance
100 megohms min. at 20°C, 500 VDC,
50% RH
Dropout
Greater than 10% of nominal coil voltage
Ambient Temperature At nominal coil voltage
Operating
-40°C (-40°F) to 70°C (158°F)
Storage
-40°C (-40°F) to 105°C (221°F)
Vibration
0.062" DA at 10–55 Hz
Shock
10 g
Enclosure
P.B.T. polyester
Terminals
Tinned copper alloy, P.C.
Max. Solder Temp.
270°C (518°F)
Max. Solder Time
5 seconds
Temperature
Max. 105°C (221°F)
Max. Solvent Temp. 80°C (176°F)
NOTES
1. All values at 20°C (68°F).
2. Relay may pull in with less than “Must Operate” value.
3. Minimum permissible contact load:
SCO contact: 100 mA at 5 VDC
SCO contact with gold plating: 10 mA at 5 VDC
4. Specifications subject to change without notice.
Max. Immersion Time 30 seconds
Weight
3 grams
ZETTLER electronics
Logistic Design (UK) Limited. Unit 3, Eagle Centre Way, Luton LU4 9US www.zettlerrelay.com [e-mail]
Telephone [phone] Fax [phone]
2000-08-31