115058-14 Datasheet, PDF (1/3 Pages) List of Unclassifed Manufacturers – Type VR Vertical Mounting Clamp

Type VR Vertical Mounting Clamp
Capacitor Hardware
Diameter
of Part to be
Catalog Part Number
Unassembled Assembled
Without
Screw & Nut
with
Dimensions
A
B
C
CDE VR mounting clamps may
be used to mount any cylindrical
capacitor with a 1” to 3” diameter
that is to be mounted in a vertical
position. Material is 1010 CRS,
commercial grade #4 temper
ASI scale. Parts are finished with
.0001 (nominal) zinc chromate
plating. Use for mounting CG
types, PSU, SF and MPF types.
Material thickness is .035”
Mounted
1" to 1-1/16
1-3/8" to 1-7/16
1-1/2" to 1-9/16
1-3/4" to 1-13/16
2" to 2-1/16
2-1/2" to 2-9/16
3" to 3-1/8
Screw
Nut
Screw & Nut
VR1B
VR3B
VR4B
VR6B
VR8B
VR10B
VR12B
VRSCREW
VRNUT
VR1, 3 & 4
.219”
.375”
B Mtg
2 Holes
.1561” Dia.
.156”
.562” _.750”
Included
VR1
VR3
VR4
VR6
VR8
VR10
VR12
—
—
Screw & Nut
VR1A
VR3A
VR4A
VR6A
VR8A
VR10A
VR12A
—
—
1"
1-7/16" 1-7/8*"
1-3/8" 1-25/32" 2-7/32"
1-1/2" 1-15/16" 2-11/32"
1-3/4" 2-1/4" 2-9/16"
2"
2-1/2" 2-13/16"
2-1/2" 3"
3-5/16"
3"
3-7/16" 3-13/16"
9/16" long 6-32 thread NC-2A
Standard hex nut to fit screws
VR6, 8,10 & 12
C ±0.01”
B Mtng ±0.03”
0.176” x 0.281”
±0.016 (3 places).
120 º ±3 º
0.01.8384”4”±0±.00.1061”6”
(3 Places)
75 º
A ±0.016”
B Mtng ±0.03”
Ø 0.201” ±0.005”
0.375”±0.016”
1.125” ±0.016”
Type TH Horizontal Mounting Clip
0.035”
0.075” ±0.016”
0.500” ±0.016”
.*340” except TH25 is .590”
B
A
.135” Dia
Hole
.594”
Dimensions in Inches
Nominal Dia.
Catalog
of Part to be
Part Number Mounted
A
B
TH13
TH17
TH21
TH23
TH25
.375
.625
.875
1.000
1.375
.250
.312
.312
.312
.312
.47
.72
1.00
1.06
1.50
These clips, though designed
for capacitors, have varied ap-
plications to retain many cylin-
drical components. They are
used extensively in the electrical
and electronic industries to hold
spindles, condensers, capaci-
tors, tubes, rods and conduit.
Clips have phosphate and oil
finish.
Material thickness TH13 thru
TH17 is .016”. TH21 thru TH25
is .020”
ACR15KT Motor Start Resistor Kit
ACR220KT Motor Run Resistor Kit
15K Ohm 2 watt bleeder resistors for AC motor start applica-
tions. Saves relay switch contacts and capacitor, particularly
in capacitor start applications. 1/4” quick connect terminals
eliminate need for soldering.
220K Ohm 1 watt bleeder resistors for AC motor run applica-
tions. Saves relay switch contacts and capacitor, particularly
in capacitor run applications. 1/4” quick connect terminals
eliminate need for soldering.
ACR15K:
ACR220K:
Pack of 10, 15K Ohm 2 watt bleeder resistor without quick Pack of 10, 220K Ohm 1 watt bleeder resistor without quick
connect terminals.
connect terminals.
CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: [phone] • Fax: [phone] • www.cde.com