GD16521 Datasheet, PDF (9/13 Pages) List of Unclassifed Manufacturers – 2.5 GBIT/S RE TIMING LASER DRIVER

DC Characteristics
T_CASE = -40 °C to +95 °C, appropriate heat sinking may be required, for package parts. Device is DC-tested in the temperature
range 0 °C to 85 °C, specifications from -40 °C to 95 °C are guaranteed by design.
T_{DIE BACK} = -30 °C to +100 °C, appropriate heat sinking may be required, for dies. Die is DC-tested at the temperature 85 °C, specifi-
cations from -30 °C to +100 °C are guaranteed by design.
All voltages in table are referred to VEE. All input signal and power currents in table are defined positive into of the pin. All output
signal currents in table are defined positive out of the pin.
Symbol:
V_CC
I_CC
P_DISS
V_Diff CML IN
V_CM CML IN
Z_IN CML
I_HI CML IN
I_LO CML IN
V IMSET
V IMM/IMC
V PD/OPSET
I_SINK IMM
I_SINK IMB
D _ABSIM/IMM
D _RELIB/IBM
D _ABSIB/IBM
D _RELIB/IBM
V_IN IBSET
V_IN DUTY
R_IN DUTY
V_HI LVTTL
V_LO LVTTL
I_HI LVTTL
I_LO LVTTL
V_O IB
I IB
I_SD IB
V_O IM
I_Mod,HI IM
I_Mod,LO IM
I_SD IM
Characteristic:
Power Supply
Supply Current
Power Dissipation
CML input voltage swing.
Common mode voltage for CML input.
CML input impendance
CML input HI current
CML input LO current
Voltage Range for IMSET
Voltage Range IMM and IMC
Voltage Rang PD and OPSET
Sink Current into pin IMM
Sink Current into pin IMB
Absolute Modulation current monitor deviation
from I_IM /20
Relative Modulation current monitor error over
temperature, supply voltage, and modulation
current
Absolute Pre-bias current monitor deviation
from I_IB /20
Relative Pre-bias current monitor error over
temperature, supply voltage, and bias current
Input Voltage Range for IBSET
Input Voltage Range for DUTY
Input impedance for DUTY
Input High Voltage for FFSET and SHDW
Input Low Voltage for FFSET and SHDW
Input High Current for FFSET and SHDW
Input Low Current for FFSET and SHDW
IB Output Voltage
IB Current
IB Current shutdown mode
IM Output Voltage
IM High Modulation Current
IM Low Modulation Current
IM Current shutdown mode
Conditions:
I_IM/IMB = 0 A,
I_IB = 0 A
V_{CC =} 3.3 V,
I_IM/IMB = 0 A,
I_IB = 0 A
Note 4
Note 4
Note 3
Note 3
T_CASE = -10 °C to
+95 °C
T_CASE = -40 °C to
+95 °C
I_IBM / I_IM
SHDW = “1"
Note 2
Note 1
SHDW = “1"
MIN.:
+2.97
-170
TYP.:
+3.3
-125
410
MAX.:
+3.6
-110
UNIT:
V
mA
mW
300
1.8
35
-10
0
2.5
2.5
-4
-8
-5
-2
-3
-4
-2
0
0
1
2
0
-500
V_EE +1
-100
-25
V_EE +1
-70
-3
-25
800
mV
V_CC - 0.5
V
50
65
W
10
mA
mA
V_CC
V
V_CC
V
V_CC
V
mA
mA
5
%
2
%
3
%
4
%
2
%
V_CC
V
V_CC /2
V
TBD
kW
V_CC
V
0.8
V
50
mA
mA
V_EE +5
V
0
mA
mA
V_EE +5
V
0
mA
1
mA
mA
Data Sheet Rev.: 11
GD16521
Page 9 of 13