RXE010 Datasheet, PDF (7/12 Pages) List of Unclassifed Manufacturers – PolySwitch RXE device

Electrical characteristics (20°C)
RXE Product Data
RXE
Radial Leaded
Now that you have selected your RXE device, please review the
device’s characteristics in this section to verify that the device will
perform as required.
Part
IH
Number (A)
RXE010 0.10
IT
(A)
0.20
Max. time
to trip (s) Pd
at 5 x IH
(W)
4.0
0.38
Initial resistance
R min.
(Ω)
R max.
(Ω)
2.50
4.50
RXE017 0.17
0.34
3.0
0.48
3.30
5.21
RXE020 0.20
0.40
2.2
0.41
1.83
2.75
RXE025 0.25
0.50
2.5
0.45
1.25
1.95
RXE030 0.30
0.60
3.0
0.49
0.88
1.33
RXE040 0.40
0.80
3.8
0.56
0.55
0.86
RXE050 0.50
1.00
4.0
0.77
0.50
0.77
RXE065 0.65
1.30
5.3
0.88
0.31
0.48
RXE075 0.75
1.50
6.3
0.92
0.25
0.40
RXE090 0.90
1.80
7.2
0.99
0.20
0.31
RXE110 1.10
2.20
8.2
1.50
0.15
0.25
RXE135 1.35
2.70
9.6
1.70
0.12
0.19
RXE160 1.60
3.20
11.4
1.90
0.09
0.14
RXE185 1.85
3.70
12.6
2.10
0.08
0.12
RXE250 2.50
5.00
15.6
2.50
0.05
0.08
RXE300 3.00
6.00
19.8
2.80
0.04
0.06
RXE375 3.75
7.50
24.0
3.20
0.03
0.05
IH = Hold current—maximum current at which the device will not trip at 20°C.
IT = Trip current—minimum current at which the device will always trip at 20°C.
P_d = Typical power dissipation—typical amount of power dissipated by the device when in tripped state in 20°C still air.
R min. = Minimum device resistance at 20°C prior to tripping.
R max. = Maximum device resistance at 20°C prior to tripping.
R₁ max. = Maximum device resistance at 20°C measured 1 hour post trip.
Physical characteristics
Post-trip resistance
R1 max .
(Ω)
7.50
8.00
4.40
3.00
2.10
1.29
1.17
0.72
0.60
0.47
4
0.38
0.30
0.22
0.19
0.13
0.10
0.08
Lead material
Soldering characteristics
Insulating material
RXE010: Tin coated nickel-copper alloy, 24 AWG, ∅ 0.51 mm/0.020 in
RXE017–040: Tin/lead-plated copper-clad steel, 24 AWG, ∅ 0.51 mm/0.020 in
RXE050–090: Tin/lead-plated copper, 24 AWG, ∅ 0.51 mm/0.020 in
RXE110–375: Tin-plated copper, 20 AWG, ∅ 0.81 mm/0.032 in
Solderability per MIL-STD-202, Method 208E
Solder heat withstand per MIL-STD-202, Method 210, Condition B
Cured, flame-retardant epoxy polymer; meets UL 94V-O
requirements
Note: Devices are not designed to be placed through a reflow process.
Raychem Circuit Protection Devices
RXE Devices 171