GM7630 Datasheet, PDF (4/5 Pages) List of Unclassifed Manufacturers – FIXED MULTI - OUTPUT REGULATOR

AA
MICROELECTRONICS
Power Management
GM7630
FIXED MULTI - OUTPUT REGULATOR
ELECTRICAL CHARACTERISTICS
(Refer to test circuit V_IN1=7.5V, V_IN2=10.5V, T_J= 25°C, unless otherwise specified)
Parameter
Output Voltage 1
Output Voltage 2
Dropout Output Voltage 1,2
Line Regulation 1,2
Load Regulation 1, 2
Output Voltage 3
Line Regulation 3
Load Regulation 3
Reset Pulse Delay
Saturation Voltage in Reset
Condition
Leakage Current Pin 6
Output Voltage Thermal Drift
Short Circuit Output Current
Disable Voltage High
Disable Voltage Low
Disable Bias Current
Junction Temperature for TSD
Quiescent Current
Reset Threshold Voltage
Reset Threshold Hysteresis
Symbol
V_O1
V_O2
Vd1,2
DV_O1,2
DV_O1,2
V_O3
DV_O3
DV_O3
Trd
VrL
IrH
STt
Isc 1,2
VdisH
VdisL
Idis
Ttsd
Iq
Vr
Vrth
Condition
I_O1=10mA,
7.5V< V_IN1< 14V
5mA < I_O1< 500mA
I_O2=10mA,
10.5V< V_IN2< 18V
5mA < I_O2< 500mA
I_O1,2=500mA,
7.5V< V_IN1< 14V
10.5V < V_IN2< 18V
I_O1,2= 200mA
5mA < I_O1 < 500mA
5mA < I_O2< 500mA
Vsys= 13V, I_O3= 100mA
13V <V_IN3< 18V
I_O3= 100mA
5mA < I_O3 < 1A
Cd= 100nF, Note 1
I6= 5mA
V6= 10V
0°C < T_J < +125°C, Note 2
V_IN1=7.5V, V_IN 2= 10.5V
Output 2 Active
Output 2 Disabled
0V < Vdis < 7V
Note 2
I_O1= 10mA, Output2 Disabled
K= V_O1
Note 1
Min ^Typ Max Unit
5.0
5.1 5.2
4.9
5.1 5.3
V
7.84 8 8.16
7.7
8
8.3
V
-
-
2.5
V
-
-
50
80
mV
-
100
0.1
mV
160
11.7 12 12.3
V
-
-
120 mV
-
-
250 mV
-
25
-
ms
-
-
0.4
V
-
-
-
100
-
-
2.0
-
-
-
-100
-
-
145
-
-
10
µA
- _ppm/°C
1.6
A
-
V
0.8
V
2
µA
-
°C
2
mA
K -0.4 K -0.25 K -0.1 V
20
50 100 mA
Notes:
1. To check the reset circuit ,the reset output is low to discharge the delay capacitor(=Cd). if it’s less than V_O1-0.25V.
And the reset output is high when the delay capacitor voltage linearly increased by the interal current source(10µA)
if it’s more than V_O1- 0.2V. The equations of delay time is same as below. Trd = (Cd X 2.5) / 10µA
4 ^{2. These parameters, although guaranteed, are not 100% tested in production.}