|
CM8563 Datasheet, PDF (4/7 Pages) List of Unclassifed Manufacturers – 1.5A LINEAR BUS TERMINATION REGULATOR | |||
|
◁ |
CM8563
1.5A LINEAR BUS TERMINATION REGULATOR
ABSOLUTE MAXIMUM RATINGS
Absolute maximum ratings are those values beyond which the
device could be permanently damaged.
VIN, VCCA, VDDQ to GND ......................â¦.â¦â¦... â0.3V to 6V
Storage Temperature â¦â¦.............â¦â¦..â¦â¦. -65°C to 150°C
OPERATING RANGE (Note 1)
Lead Temperature (Soldering, 5 sec)â¦â¦â¦â¦â¦â¦.. 260°C
Thermal Resistanceï¨(θJC )â¦.. â¦â¦â¦.. .14°C/W (PSOP-8)
Thermal Resistanceï¨(θJC )â¦.. â¦â¦â¦ 15.7°C/W (SOP-8)
Junction Temperature Range (Note 2) â¦â¦â¦â¦â¦â¦.. 0°C to 125°C
VCCA to GND â¦â¦â¦â¦â¦â¦â¦â¦â¦â¦â¦â¦â¦â¦â¦â¦â¦... 2.2V to 5.5V
VIN to GND â¦â¦â¦â¦â¦â¦â¦â¦â¦â¦â¦â¦â¦â¦â¦â¦â¦... 2.2V to VCCA
ELECTRICAL CHARACTERISTICS (Unless otherwise stated, these specifications apply TA=25°C;
VCCA=VIN=+2.5V and VDDQ=+2.5V (Note 3)) maximum ratings are stress ratings only and functional device operation is not
implied.
Symbol
Parameter
VREF
VREF Voltage
VOS
VOUT Output Voltage Offset
ï½ÎVLOADï½
ZVREF
ZVDDQ
Load Regulation
(Note 5)
VREF Output Impedance
VDDQ Output Impedance
ICCQ
Quiescent Current
Power Good (Note 7)
Test Conditions
IREFOUT=0mA
IOUT=0A
(Note 4)
IOUT: 0A -> 1.5A
IOUT: 0A -> -1.5A
IREF= -5uA to +5uA
IOUT=0A
(Note 6)
CM8563
Unit
Min.
Typ.
Max.
1.21
1.235
1.26
V
-15
15
0
mV
-20
20
0.5
%
-0.5
%
5
kΩ
540
kΩ
250
400
μA
Note 1: Operating range indicates conditions for which the device is intended to be functional, but does not guarantee specific
performance limits. For guaranteed specification and test conditions see Electrical Characteristics.
Note 2: At elevated temperatures, devices must be derated based on the thermal resistance. The SO-8 package must be derated
atθJA = 151â/W junction to ambient with no heat sink.
Note 3: Limits are 100% production tested at 25â. Limits over the operating temperature range are guaranteed through
correlation using Statistical Quality Control methods.
Note 4: VOS = VREF â VOUT
Note 5: Load regulation is tested by using a 10ms current pulse and measuring VOUT.
Note 6: Quiescent current defined as the current flow into VCCA.
Note 7: PG function but LP2995 does not have it. PG will be high as VTT is larger than 90% VREF, and PG will change to low
as VTT is lower than 85% VREF. PG also will be low as VTT is greater than 115% VREF, and PG will change to high as
VTT is lower than 110% VREF. It has both directions PG function.
2003/03/28
Champion Microelectronic Corporation
Page 4
|
▷ |