JBX Datasheet, PDF (3/6 Pages) List of Unclassifed Manufacturers – JBX PLUG ASSEMBLY INSTRUCTIONS

3. When assembling a plug with a protective boot (#3), prep the cable by taking the protective
boot and sliding it with the small inside diameter first onto the cable. Then slide the end of the
back nut (#2) that has the smaller diameter onto the cable. Next, take the collet (#1) and slide
the end with the gripping teeth first onto the cable until the opposite end of the collet is flush
with the cut end of the jacket. If the cable has shielding, fold back the braid so that it is
covering the outside diameter of the collet. Do not place braid into any area of the alignment
slots. Then insure that the braid does not interfere with the alignment slots of the collet.
Gripping Teeth
4. Attach removable contacts to wires:
a. If using crimped contacts, crimp the contacts onto the ends of the exposed wires using
the proper crimping tool set on the correct AWG wire. (see FIGURE 4.A). After the
contact has been crimped to the wire, check each contact to insure that the contact is
securely crimped to the wire.
Locator for pin and socket 0.7 - 0.9 mm and 1.3 mm contacts
Shell
size
0
1
2
3
FIGURE 4.A
Ø
contacts ^AWG
0.7
22 - 24 – 26
0.9
20 - 22 – 24
0.7
22 - 24 – 26
0.9
20 - 22 – 24
1.3
18 - 20 – 22
0.7
22 - 24 – 26
0.9
20 - 22 – 24
1.3
18 - 20 – 22
0.7
22 - 24 – 26
0.9
20 - 22 – 24
1.3
18 - 20 – 22
Male contact
SOURIAU P/N
DANIELS P/N ASTRO P/N SOURIAU P/N
JBX 0 OUT LP07 86 – 223
JBX 0 OUT LP09 86 – 225
JBX 1 OUT LP07 86 – 196
JBX 1 OUT LP09 86 – 198
JBX 1 OUT LP13 86 – 200
JBX 2 OUT LP07 86 – 202
JBX 2 OUT LP09 86 – 204
JBX 2 OUT LP13 86 – 206
JBX 3 OUT LP07 86 – 217
JBX 3 OUT LP09 86 – 218
JBX 3 OUT LP13 86 – 219
/
/
642 – 001
642 – 002
642 – 003
642 – 007
642 – 008
642 – 009
642 – 014
642 – 015
642 – 016
JBX 0 OUT LS07
JBX 0 OUT LS09
JBX 1 OUT LS07
JBX 1 OUT LS09
JBX 1 OUT LS13
JBX 2 OUT LS07
JBX 2 OUT LS09
JBX 2 OUT LS13
JBX 3 OUT LS07
JBX 3 OUT LS09
JBX 3 OUT LS13
Female contact
DANIELS P/N ASTRO P/N
86 – 224
86 – 226
86 – 197
86 – 199
86 – 201
86 – 203
86 - 205
86 – 207
86 – 214
86 – 215
86 – 216
/
/
642 – 004
642 – 005
642 – 006
642 – 010
642 – 011
642 – 012
642 – 017
642 – 018
642 - 019
Turret with locator for pin and socket 1.6 mm and 2 mm contacts
Shell size
2
3
Ø contacts
1.6
2
1.6
2
AWG
14 - 16 – 18
12 - 14 – 16
14 - 16 – 18
12 - 14 – 16
SOURIAU P/N
JBX 2 OUT LT16
JBX 2 OUT LT20
JBX 3 OUT LT16
JBX 3 OUT LT20
Male and female contacts
DANIELS P/N
ASTRO P/N
TH 564
650 – 030
TH 565
650 – 031
TH 566
650 – 038
TH 567
650 - 035
REV 4 – April 14, 2004