MLP7100 Datasheet, PDF (2/2 Pages) List of Unclassifed Manufacturers – Limiter Diodes

Control Devices: MLP 7100 Series
Electrical Characteristics
Vb
Cj0
TYP
TYP
(V)
(pF)
20-45
0.20
-
0.50
-
0.70
45-75
0.20
-
0.50
-
0.70
120-180
0.20
-
0.60
-
0.80
15-30
0.12
-
0.20
30-60
0.12
-
0.20
Cj6
Rs Typ⁶
Rs Typ⁶
Tl
θ_p¹
Maximum
MAX
@ 10 mA @ 10 mA
TYP
TYP Thermal Resistance Part
(pF)
(Ω)
(Ω)
(nS) (°C/W)
(°C/W)
Number
0.15
1.5
0.30
1.2
0.50
1.0
0.15
1.5
0.30
1.2
0.50
1.0
0.15
1.5
0.30
1.0
0.50
0.5
0.10
2.0
0.15
1.5
0.10
2.0
0.15
1.5
5.0
5
20
4.5
10
12
4.0
10
10
4.0
10
15
3.5
15
10
3.0
20
6
3.5
50
1.2
3.0
50
0.5
3.0
100
0.3
4.0
530
12
3.0
520
8
4.0
720
10
4.0
715
7
100
MLP7100
80
MLP7101
55
MLP7102
80
MLP7110
60
MLP7111
40
MLP7112
40
MLP7120
20
MLP7121
15
MLP7122
0
MLP7130
0
MLP7131
0
MLP7140
0
MLP7141
Max. Peak
Pin
@1.0 µs
(dBm)
Typical
Threshold²
(dB)
Leakage²
Pout
TYP
(dBm)
Insertion Loss³
TYP
(dB)
CW⁴
Pin
MAX (W)
Recovery⁵
Time, Typ
(nS)
Part
Number
+50
+10
+22
+53
+10
+24
+56
+10
+25
+53
+15
+27
+56
+15
+29
+59
+15
+31
+60
+20
+39
+63
+20
+41
+66
+20
+44
+47
+7
+19
+50
+7
+22
+47
+12
+24
+50
+12
+27
0.1
21
0
MLP7100
0.2
31
0
MLP7101
0.2
41
0
MLP7102
0.1
32
0
MLP7110
0.2
42
0
MLP7111
0.2
52
0
MLP7112
0.1
55
0
MLP7120
0.2
10
50
MLP7121
0.2
15
50
MLP7122
0.1
2
5
MLP7130
0.1
3
5
MLP7131
0.1
3
10
MLP7140
0.1
4
10
MLP7141
Notes:
1. Pulsed thermal impedance is given for a 1 µs pulse. CW thermal impedance presumes infinite heat sink.
2. Threshold input power produces 1 dB increase in insertion loss. Figure shows typical leakage power curves. Data taken
for 1.0 GHz.
3. Chip loss can be represented as a resistance in shunt with the junction capacitance. Rp is measured at 3 GHz, zero
Bias. Loss data shown are for 10 GHz for 0.15 and 0.30 pF chips, 5 GHz for 0.50 pF chips. Loss is measured at -10
dBm input.
4. Note that CW power and average power are not synonymous. Power ratings are computed in terms of a peak
junction temperature of 200°C, for short pulses, an average junction temperature of 125°C, and an ambient of 25°C.
Duty factor 0.001 assumed for maximum pulse power input. Figure shows power derating with temperature.
5. Recovery time is measured with ground return (less than 1.0 Ohm) to 1 dB excess loss, at 1 GHz.
6. Series resistance is measured at 500 MHz.
7. Limiter diodes with higher capacitance and/or higher breakdown voltage for very high power applications are
available on request.
Maximum Ratings
Operating Temperature
Maximum Leakage Current
-55°C to +150°C
0.5 mA at 88% of minimum rated breakdown
MicroMetrics, Inc. 136 Harvey Road, Building C, Londonderry, NH 03053
Voice: 603-641-3800, Fax: [phone], Internet: www.micrometrics.com, E-mail: [e-mail]
35