1N6373A Datasheet, PDF (2/6 Pages) Motorola, Inc – Zener Transient Voltage Suppressors Unidirectional and Bidirectional

*ELECTRICAL CHARACTERISTICS (TA = 25°C unless otherwise noted) VF# = 3.5 V Max, IF** = 100 A) (C suffix denotes standard
ELECTRICAL CHARACTERISTICS back to back bidirectional versions. Test both polarities)
JEDEC
Device
Note 1
1N6373
1N6374
1N6382
Device
Note 1
ICTE-5/MPTE-5
ICTE-8/MPTE-8
ICTE-8C/MPTE-8C
Breakdown{{
Voltage
VBR
Volts @ IT
Min (mA)
Maximum
Reverse
Stand-Off
Voltage
VRWM***
(Volts)
Maximum
Reverse
Leakage
@ VRWM
IR (µA)
Maximum
Reverse
Surge
Current
IRSM{
(Amps)
Maximum
Reverse
Voltage
@ IRSM{
(Clamping
Voltage)
VRSM
(Volts)
6
1
5
9.4 1
8
9.4 1
8
300
160
9.4
25
100
15
25
100
15
Clamping Voltage
Peak Pulse
Current @
Ipp1{ = 1 A
VC1
(Volts max)
7.1
11.3
11.4
Peak Pulse
Current @
Ipp1{ = 10 A
VC2
(Volts max)
7.5
11.5
11.6
1N6375
ICTE-10/MPTE-10
11.7 1
10
2
90
16.7
13.7
14.1
1N6383
ICTE-10C/MPTE-10C 11.7 1
10
2
90
16.7
14.1
14.5
1N6376
ICTE-12/MPTE-12
14.1 1
12
2
70
21.2
16.1
16.5
1N6384
ICTE-12C/MPTE-12C 14.1 1
12
2
70
21.2
16.7
17.1
1N6377
ICTE-15/MPTE-15
17.6 1
15
2
60
25
20.1
20.6
1N6385
ICTE-15C/MPTE-15C 17.6 1
15
2
60
25
20.8
21.4
1N6378
ICTE-18/MPTE-18
21.2 1
18
2
50
30
24.2
25.2
1N6386
ICTE-18C/MPTE-18C 21.2 1
18
2
50
30
24.8
25.5
1N6379
ICTE-22/MPTE-22
25.9 1
22
2
40
37.5
29.8
32
1N6387
ICTE-22C/MPTE-22C 25.9 1
22
2
40
37.5
30.8
32
1N6380
ICTE-36/MPTE-36
42.4 1
36
2
23
65.2
50.6
54.3
1N6388
ICTE-36C/MPTE-36C 42.4 1
36
2
23
65.2
50.6
54.3
1N6381
ICTE-45/MPTE-45
52.9 1
45
2
19
78.9
63.3
70
1N6389
ICTE-45C/MPTE-45C 52.9 1
45
2
19
78.9
63.3
70
NOTE 1: C suffix denotes standard back-to-back bidirectional versions. Test both polarities. JEDEC device types 1N6382 thru 1N6389 are registered as back to back bidirectional versions and
do not require a C suffix. 1N6373 thru 1N6381 are registered as unidirectional devices only (no bidirectional option).
*** Indicates JEDEC registered data.
*** 1/2 sine wave (or equivalent square wave), PW = 8.3 ms, duty cycle = 4 pulses per minute maximum.
*** A transient suppressor is normally selected according to the maximum reverse stand-off voltage (VRWM), which should be equal to or greater than the dc or continuous peak operating
*** voltage level.
{ { Surge current waveform per Figure 5 and derate per Figure 2 of the General Data — 1500 W at the beginning of this group.
{ { VBR measured at pulse test current IT at an ambient temperature of 25°C.
# VF applies to unidirectional devices only.
500 Watt Peak Power Data Sheet
4-2
Motorola TVS/Zener Device Data