SM31E Datasheet, PDF (1/8 Pages) List of Unclassifed Manufacturers – Self-contained DC-operated Opposed Mode Sensors

MINI-BEAM^® SM31E/SM31R and SM31EL/SM31RL
Self-contained DC-operated Opposed Mode Sensors
• Compact, self-contained opposed mode modulated
infrared sensor pairs for 10-30V dc operation
• Standard sensor pairs have 3 m (10 ft) range
• Long range sensor pairs have 30 m (100 ft) range
• Switch-selectable for light operate or dark operate; Highly
repeatable, 1 millisecond response
• Both sourcing and sinking outputs (150 mA maximum ea.)
• Receivers include Banner’s exclusive AID™ alignment
system, US patent number 4356393
• Rugged, epoxy-encapsulated construction: meets NEMA
standards 1, 2, 3, 3S, 4, 4X, 6, 12 and 13, IEC IP67
• Physically and electrically interchangeable with 18 mm
barrel-type photoelectrics
Models
SM31E
SM31R
SM31EQD
SM31RQD
MINI-BEAM Opposed-Mode Emitter (E) and Receiver (R) Models
Infrared, 880 nm
Range
Cable*
Supply
Voltage
Output
Type
Excess Gain
Beam Pattern
3m
(10')
2 m (6.5')
2 m (6.5')
4-Pin Euro QD
4-Pin Euro QD
10-30V dc
Bipolar
NPN/PNP
1000
E
X
C
E ¹⁰⁰
S
S
G ¹⁰
A
I
N
1
.01 m
.033 ft
SM31E & SM31R
Opposed Mode
300 mm
200 mm
100 mm
0
100 mm
200 mm
300 mm
SM31E & SM31R
Opposed Mode
12.0 in
8.0 in
4.0 in
0
4.0 in
8.0 in
12.0 in
.10 m
.33 ft
1.0 m
3.3 ft
10 m
33 ft
DISTANCE
0
.6 m 1.2 m 1.8 m 2.4 m 3.0 m
2 ft
4 ft
6 ft
8 ft 10 ft
DISTANCE
SM31EL
SM31RL
SM31ELQD
SM31RLQD
30 m
(100')
2 m (6.5')
2 m (6.5')
4-Pin Euro QD
4-Pin Euro QD
10-30V dc
Bipolar
NPN/PNP
1000
E
X
C
E ¹⁰⁰
S
S
G ¹⁰
A
I
N
1
.1 m
.33 ft
SM31EL & SM31RL
Opposed Mode
750 mm
500 mm
250 mm
0
250 mm
500 mm
750 mm
SM31EL & SM31RL
Opposed Mode
30.0 in
20.0 in
10.0 in
0
10.0 in
20.0 in
30.0 in
1.0 m
3.3 ft
10 m
33 ft
DISTANCE
100 m
330 ft
0
6 m 12 m 18 m 24 m 30 m
20 ft 40 ft 60 ft 80 ft 100ft
DISTANCE
*NOTES:
i) 9 m (30') cables are available by adding suffix “W/30” to the model number of any cabled sensor (e.g., SM31EL W/30).
ii) A 150 mm (6") long pigtail cable with attached QD connector is available by adding suffix “QDP” to the model number of any
MINI-BEAM sensor (e.g., SM31ELQDP). See page 5 for more information.
iii) A model with a QD connector requires an accessory mating cable. See page 8 for more information.
iv) Emitters and receivers may be ordered with 0.3 millisecond on/off response by adding suffix “MHS” to the model numbers
(e.g., SM31EMHS & SM31RMHS). This modification reduces sensing range (and excess gain).
Printed in USA
05/01
P/N 03560 rev. C