|
SLN02G64D2BK1MT-CCRT Datasheet, PDF (1/17 Pages) List of Unclassifed Manufacturers – 2048MB DDR3L . SDRAM SO-DIMM | |||
|
Data Sheet
Rev.1.0 21.11.2012
2048MB DDR3L â SDRAM SO-DIMM
204 Pin SO-DIMM
SLN02G64D2BK1MT-xxRT
Features:
ï§ 204-pin 64-bit DDR3 Small Outline Dual-In-Line Double
Data Rate Synchronous DRAM module
2GByte in FBGA Technology
RoHS compliant
ï§ Module organization: single rank 256M x 64
ï§ VDD = 1.35V and 1.5V
ï§ VDDQ = 1.35V and 1.5V
ï§ SSTL_15 compatible
ï§ Fly-by-bus with termination for C/A & CLK bus
Options:
ï§ On-board I2C temperature sensor with integrated serial
ï§ Data Rate / Latency
DDR3 1333 MT/s CL9
DDR3 1600 MT/s CL11
Marking
-CC
-DC
presence-detect (SPD) EEPROM
ï§ Gold-contact pads
ï§ This module is fully pin and functional compatible to the
JEDEC PC3-12800 spec. and JEDEC- Standard MO-268.
ï§ Module Density
2048MB with 8 dies and 1 rank
(see www.jedec.org)
ï§ The pcb and all components are manufactured according
to the RoHS compliance specification [EU Directive
ï§ Standard Grade
(TA) 0°C to 70°C
(TC) 0°C to 85°C
2002/95/EC Restriction of Hazardous Substances (RoHS)]
ï§ DDR3 - SDRAM component Micron
MT41K256M8DA-125 DIE-Rev. K
ï§ 256Mx8 DDR3 SDRAM in PG-TFBGA-78 package
ï§ 8-bit prefetch architecture
ï§ Programmable CAS Latency, CAS Write Latency, Additive
*) The refresh rate has to be doubled when 85°C<TC<95°C*) The refLreasthenractye,hBausrtsot bLeednoguthbleadndwhBeunrs8t5°TCy<pTeC.<95°C
Environmental Requirements:
ï§ On-Die-Termination (ODT) and Dynamic ODT for improved
signal integrity.
ï§ Operating temperature (ambient)
Standard Grade
0°C to 70°C
ï§ Refresh. Self Refresh and Power Down Modes.
ï§ ZQ Calibration for output driver and ODT.
ï§ System Level Timing Calibration Support via Write Leveling
ï§ Operating Humidity
10% to 90% relative humidity, noncondensing
ï§ Operating Pressure
105 to 69 kPa (up to 10000 ft.)
ï§ Storage Temperature
-55°C to 100°C
ï§ Storage Humidity
5% to 95% relative humidity, noncondensing
ï§ Storage Pressure
1682 PSI (up to 5000 ft.) at 50°C
and Multi Purpose Register (MPR) Read Pattern.
Figure: mechanical dimensions1
Swissbit AG
Industriestrasse 4
CH â 9552 Bronschhofen
Fon: +41 (0) 71 913 03 03
Fax: +41 (0) 71 913 03 15
1if no tolerances specified ± 0.15mm
www.swissbit.com
eMail: info@swissbit.com
Page 1
of 17
|
▷ |