|
SGU02G72H1BG2SA-BBRT Datasheet, PDF (1/15 Pages) List of Unclassifed Manufacturers – 2048MB DDR3 – SDRAM Ultra Low Profile ECC DIMM | |||
|
Data Sheet
Rev.1.0 04.02.2011
2048MB DDR3 â SDRAM Ultra Low Profile ECC DIMM
240 Pin unbuffered ECC DIMM
SGU02G72H1BG2SA-xxRT
2GByte in FBGA Technology
RoHS compliant
Options:
ï§ Data Rate / Latency
DDR3 1066 MT/s CL7
DDR3 1333 MT/s CL9
Marking
-BB
-CC
ï§ Module density
2048MB with 18 dies and 2 ranks
ï§ Standard Grade
(TA)
0°C to 70°C
(TC
0°C to 85°C
Environmental Requirements:
ï§ Operating temperature (ambient)
Standard Grade
0°C to 70°C
ï§ Operating Humidity
10% to 90% relative humidity, noncondensing
ï§ Operating Pressure
105 to 69 kPa (up to 10000 ft.)
ï§ Storage Temperature
-55°C to 100°C
ï§ Storage Humidity
5% to 95% relative humidity, noncondensing
ï§ Storage Pressure
1682 PSI (up to 5000 ft.) at 50°C
Features:
ï§ 240-pin 72-bit unbuffered Dual-In-Line Double Data Rate
Synchronous DRAM Module with ECC
ï§ Module organization: dual rank 256 x 72
ï§ VDD = 1.5V ±0.075V, VDDQ 1.5V ±0.075V
ï§ 1.5V I/O ( SSTL_15 compatible)
ï§ Fly-by-bus with termination for C/A & CLK bus
ï§ Supports ECC, error detection and correction
ï§ Ultra Low Profile (ULP)
ï§ On-board I2C temperature sensor with integrated serial
presence-detect (SPD) EEPROM
(according to JEDEC JESD21C)
ï§ Gold-contact pad
ï§ This module family is fully pin and functional compatible
to JEDEC PC3-12800 spec and MO-269.
(see www.jedec.org)
ï§ The pcb and all components are manufactured according
to the RoHS compliance specification [EU Directive
2002/95/EC Restriction of Hazardous Substances
(RoHS)]
ï§ DDR3 - SDRAM component Samsung K4B1G0846G
ï§ 128Mx8 DDR3 SDRAM in PG-TFBGA-78 package
ï§ 8-bit prefetch architecture
ï§ Programmable CAS Latency, CAS Write Latency, Additive
Latency, Burst Length and Burst Type.
ï§ On-Die-Termination (ODT) and Dynamic ODT for improved
signal integrity.
ï§ Refresh. Self Refresh and Power Down Modes.
ï§ ZQ Calibration for output driver and ODT.
ï§ System Level Timing Calibration Support via Write Leveling
and Multi Purpose Register (MPR) Read Pattern.
2.20mm
Swissbit AG
Industriestrasse 4
CH-9552 Bronschhofen
54.67mm
R 0.75mm
133.35mm
R 0.70mm
R 0.70mm
Figure: mechanical dimensions1
1if no tolerances specified ± 0.15mm
Fon: +41 (0) 71 913 03 03
Fax: +41 (0) 71 913 03 15
www.swissbit.com
eMail: info@swissbit.com
Page 1
of 15
|
▷ |