PDL02-05S05 Datasheet, PDF (1/2 Pages) List of Unclassifed Manufacturers – 2 WATTS DC -DC CONVERTER

• SIP PACKAGE, 0.86 x 0.36x 0.44 INCH
• NO EXTERNAL INPUT AND OUTPUT CAPACITOR NEEDED
• 2:1 WIDE INPUT VOLTAGE RANGE
• LOW RIPPLE & NOISE
• UL94-V0 CASE POTTING MATERIALS
• INPUT TO OUTPUT ISOLATION UP TO 1KV
• CONTINUOUS SHORT CIRCUIT PROTECTION
• EXTERNAL ON/OFF CONTROL
The PDL02 series offer 2 watts of output power from a 21.8 x 9.2 x 11.1 mm package
without derating to 85ºC and without external input/output capacitor. The PDL02 series
with 2:1 wide input voltage of 4.5-9, 9-18, 18-36 and 36-75VDC and features 1000VDC
of isolation, short-circuit. The safety meets to EN60950 and UL60950. All models are
particularly suited to telecommunications, industrial, mobile telecom and test
equipment applications.
T E C H N I C A L S P E C I F I C A T I O N All specifications are typical at nominal input, full load and 25ºC otherwise noted
OUTPUT SPECIFICATIONS
Output power
2 Watts max
Voltage accuracy
Full load and nominal Vin
Minimum load (Note 1)
± 2%
25% of FL
Line regulation
LL to HL at Full Load
± 0.5%
Load regulation
25% to 100% FL
± 0.75%
Ripple and noise
20MHz bandwidth
50mVp-p
Temperature coefficient
I0.1% / ºC, max
Transient response recovery time 25% load step change
500uS typ
Short circuit protection
Continuous, automatics recovery
INPUT SPECIFICATIONS
Input voltage range
5V nominal input
12V nominal input
24V nominal input
48V nominal input
Input filter
5V input
Input surge voltage
12V input
100mS max
24V input
48V input
Reflected repple current 5V input (100uF)
There is an external
12V input (100uF)
capacitor at input (Note 2) 24V input (10uF)
48V input (10uF)
Start up time Nominal Vin and constant resistor load
4.5 – 9VDC
9 – 18VDC
18 – 36VDC
36 – 75VDC
Capacitor type
15VDC
36VDC
50VDC
100VDC
400mAp-p max
150mAp-p max
380mAp-p max
170mAp-p max
1mS typ
Remote ON/OFF
DC-DC ON
DC-DC OFF
Remote off input current Nominal input
Application circuit
Open or high impedance
Control pin applied current
3 ~ 6mA max(via 1K )
1mA max
GENERAL SPECIFICATIONS
Efficiency
See table
Isolation voltage
Isolation resistance
Isolation capacitance
1000VDC, min
10⁹ohms, min
300pF, max
Safety standard pending
IEC60950, UL60950, EN60950
Switching frequency Full load to minimum load
100 to 650KHz
Case material
Non-conductive black plastic
Base material
None
Potting material
Dimensions
Weight
MTBF (Note 3)
Silicon (UL94-V0)
0.86 X 0.36 X 0.44 Inch
(21.8 X 9.2 X 11.1 mm)
4.8g (0.17oz)
5.107 x 10⁶ hrs
ENVIRONMENTAL SPECIFICATIONS
Operating temperature range
-40ºC to +85ºC
Storage temperature range
-55ºC to +105ºC
Cooling
Nature convection
Thermal shock
MIL-STD-810D
Vibration
10~55Hz, 2G, 30minutes along X,Y and Z
Relative humidity
5% to 95% RH
EMC CHARACTERISTICS
Meet EN55022 classes B recommend
circuit with external L-C filter at input (Note
4)
5V input
12V input
24V input
48V input
100uF & 10uH
100uF & 10uH
10uF & 120uH
10uF & 120uH
EMC external circuit
DC-DC ON
+Input
1KΩ
4mA current
ctrl
Source
-Input
DC-DC OFF
+Input
1KΩ
ctrl
4mA current
Source
-Input
+
Input
-
DC-DC
Converter
+
Output
-