GU180X32D-K610A4 Datasheet, PDF (1/7 Pages) List of Unclassifed Manufacturers – Dot Graphic VFD Module

Dot Graphic VFD Module
q 180 x 32 High Brightness Dot Graphic Display
q Single 5V DC Supply
q 3 ASCII Fonts ( 5 x 5, 5 x 7, 10 x 14)
q Asynchronous, SPI & Parallel interfaces
q Wide Temperature –40 to +85°C
GU180x32D-K610A4
The module includes the VFD glass, VF drivers and
microcontroller, character generation, interface logic and patented
transformerless DC/DC converter. The interface type is selected by
a pushbutton on the back of the module. Auto key scanning and
general I/O is available on port PA0 – PA7. RS232/RS485 options.
2.5
1
13.95 24.0 31.0
1
1
CON4 CON3
CON2
19.7
79.05
117.0
124.0
18.25
6.58
CON1
3.5
3.5
1.6
6.4
Dimensions in mm & subject to tolerances.
Mounting holes 3.5mm dia.
CON3 & CON4 are not to be used in this
implementation.
ELECTRICAL SPECIFICATION
Parameter
Sym Min Typ Max Unit Condition
Supply Voltage
Vcc 4.5
5.0
5.25 V
VSS=0V
Supply Current
Icc
-
350 -
mA Vcc=5V All dots
Logic High Input
VIH
3.0
-
Vcc
V
VCC=5V
Logic Low Input
VIL
-0.5
-
1.5
V
VCC=5V
Logic High Output
VOH 4.2
-
-
V
IOH = -3mA Vcc=5V
Logic Low Output
VOL
-
-
0.6
V
IOL = 20mA
CHARACTER SETS
MINI FONT (PROPORTIONAL SPACING)
5x7 & 10x14 FONTS (FIXED SPACING)
ENVIRONMENTAL and OPTICAL SPECIFICATION
Parameter
Value
Display Area (XxY mm)
79.05 x 13.95
Dot Size/Pitch (XxY mm)
Luminance
0.29 x 0.29/0.44 x 0.44
1000 cd/m² Typ
Colour of Illumination
Blue-Green (Filter for colours)
Operating Temperature
-40°C to +85°C
Storage Temperature
-40°C to +85°C
Operating Humidity (non condensing) 10 to 90% @ 25°C
SOFTWARE COMMANDS
Hex
Command
01-07
Run Macro
08
Backspace
09
Horizontal Tab
0A
Line Feed
0B
Home
0C
Vertical Tab
0D
Carriage Return
0E
Clear End of Line
0F
Test
10 + x + y
Cursor Position
11 +xl+yt+xr+yb Set Area
12 +xl+yt+xr+yb Clear Area
13 +xl+yt+xr+yb Invert Area
14 +xl+yt+xr+yb Set Outline
15 +xl+yt+xr+yb Clear Outline
16
Set Pixel
17
Clear Pixel
18 + len + data Graphic Write
Hex
Command
19
Reset
1A + data
Write Mode - direction
1B + macro+len+data Set Macro
1B + 4D
Erase All Macros
1B + 4C/55
Lock/Unlock EEPROM
1B + 43
Request Checksum
1B + 50/46
Power On/Off
1B + 48/42
Enable/Disable Hex Write
1B + 49 + data
Set Comms
1B + 44 + data
Enable I/O Port
1B + 4F + data
Set Port Lines
1B + 52
Read Port
1B + 4B
Enable key scanning
1B + F8-FF
Brightness
1C / 1D / 1E
Select Font
1F +xl+yl+xr+yb+data Graphic Area Write^*1
20 - FF
Character Write
*1 _{Applies to version 3 software only.}
The module defaults to a 4 line of 30 character display using the 5x7 font with single pixel
spacing. The cursor position auto increments after each character write. The bottom left of a
character is placed at the cursor x,y. The M(odule) Busy line indicates the module is busy
when high. Connect the H(ost) Busy input to the MBusy to disable handshaking. Use the
button to select the configuration which is then stored in EEPROM. To send commands as
hexadecimal, prefix the 2 bytes using character 60H. Example: `10`3F`01 = Position dot x=64
y=1. To send character 60H to the display, send 60H twice.
Subject to change without notice. Doc Ref: 03872 Iss7 10 July 03
CON1
Pin Async SPI
1 5V 5V
2 Nc SCK
3 RXD /SS
4 Nc SIN
5 0V 0V
6 Nc SOUT
7 TXD /IRQ
8 /RES /RES
9 MB MB
10 HB HB
Nc = Do Not Connect
Detailed
specification,
software commands
and interface timing
are available on
request.
CON2
Pin Signal
1
0V
2
ENABLE
3
PA0
4
PA1
5
PA2
6
PA3
7
PA4
8
PA5
9
PA6
10
PA7
CONTACT
Noritake Sales Office Tel Nos
Nagoya Japan: [phone]
Canada: [phone]
Chicago USA: [phone]
Munchen (D): [phone]
Itron UK: [phone]
Rest Europe: [phone]
www.noritake-itron.com
NORITAKE ITRON VFD MODULES
GU180x32D-K610A4