English
Language : 

D221 Datasheet, PDF (1/2 Pages) List of Unclassifed Manufacturers – Single & Dual Output Miniature, 2W SIP DC/DC Converters
D200 Series
Single & Dual Output
Miniature, 2W SIP
DC/DC Converters
Key Features:
● 2W Output Power
● Miniature SIP Case
● Single & Dual Outputs
● 1,000 VDC Isolation
● >2 MHour MTBF
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Input
Parameter
Conditions
Min. Typ. Max. Units
5 VDC Input 4.5 5.0 5.5
Input Voltage Range
12 VDC Input 10.8 12.0 13.2
24 VDC Input 21.6 24.0 26.4
VDC
48 VDC Input 43.2 48.0 52.8
Input Filter
Internal Capacitor
Reverse Polarity Input Current
0.3
A
● 28 Standard Models
Output
● Industry Standard Pin-Out Parameter
Output Voltage Accuracy
Conditions
Min. Typ. Max.
±1.0 ±3.0
Units
%
Output Voltage Balance
Dual Output , Balanced Loads
±1.0
%
Line Regulation
For Vin Change of 1%
±1.2
%
Load Regulation
See Model Selection Guide
Ripple & Noise (20 MHz)
75 mV P - P
Output Power Protection
120
%
Temperature Coefficient
±0.02 %/ºC
Output Short Circuit
Momentary (0.5 Sec.)
General
Parameter
Conditions
Min. Typ. Max. Units
Isolation Voltage
60 Seconds 1,000
VDC
Isolation Resistance
500 VDC 1,000
MΩ
Isolation Capacitance
100 kHz, 1V
60
pF
Switching Frequency
125
kHz
Environmental
Parameter
Conditions
Min. Typ. Max. Units
Operating Temperature Range
Ambient -40 +25 +85
ºC
Operating Temperature Range
Case
+100
ºC
Storage Temperature Range
-40
+125
ºC
Cooling
Free Air Convection
Humidity
RH, Non-condensing
95
%
Physical
MicroPower Direct
232 Tosca Drive
Stoughton, MA 02072
USA
T: (781) 344-8226
F: (781) 344-8481
E: sales@micropowerdirect.com
W: www.micropowerdirect.com
Case Size (5V, 12V & 24V Input Models)
Case Size (48V Input Models)
Case Material
Weight
Reliability Specifications
Parameter
MTBF
Absolute Maximum Ratings
0.76 x 0.24 x 0.37 Inches (19.5 x 6.0 x 9.5 mm)
0.76 x 0.28 x 0.37 Inches (19.5 x 7.2 x 9.5 mm)
Non-Conductive Black Plastic (UL94-V0)
0.09 Oz (2.7g)
Conditions
Min. Typ. Max.
MIL HDBK 217F, 25ºC, Gnd Benign 2.0
Units
MHours
Parameter
Conditions
Min. Typ. Max. Units
5 VDC Input -0.7
9.0
Input Voltage Surge (1 Sec)
12 VDC Input -0.7
24 VDC Input -0.7
18.0
VDC
30.0
48 VDC Input -0.7
55.0
Lead Temperature
1.5 mm From Case For 10 Sec
260
ºC
Internal Power Dissipation
All Models
650
mW
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.