D12305111024 Datasheet, PDF (1/3 Pages) List of Unclassifed Manufacturers – Receiver with Demultiplex Output

Receiver with Demultiplex Output
Type D 1230 5111
Du line^®
Fieldbus Installationbus
• 8-channel receiver
• 8 : 1 demultiplex function
• 2 NPN transistor outputs
• Enable and disable output operation
• D-housing
• Plug-in type module
• LED-indications for supply and output
• AC or DC power supply
Product Description
Ordering Key
Dupline^® receiver with demul-
tiplex output (8:1) for multi-
plex transmission on Dupline^®
channels. Applicable for trans-
mitters with frequency input
(type FFD 1680, SPEC 918).
Increases the transmission
capacity of a Dupline^® system
to max. 3825 x 8-bit measu-
red values.
Type: Dupline^®
D-housing
Receiver
No. of channels
Output type
Supply
D 1230 5111 024
Type Selection
Supply Specifications
Supply
Ordering no.
8 channels
2 x 10 V/10 mA
24 VAC
120 VAC
220 VAC
D 1230 5111 024
D 1230 5111 120
D 1230 5111 220
12 VDC
D 1230 5111 712
Code Module: No code module required. D 1230 5111
automatically uses the highest available channel group of the
Dupline^® installation.
Output Specifications
Outputs
Output voltage VBB
Reverse polarity
protection
Current per output
Total load capability
Short-circuit protection
Built-in protective diodes
Off-state leakage current
Output voltage drop
Cable length
Dielectric voltage
Output - Dupline^®
Response time
1 NPN
transistor
(enable)
10 VDC
Yes
≤ 2.5 mA
100%
None
None
≤ 100 µA
≤ 1.2 V
≤3m
≥ 2 kVAC (rms)
< 1 pulse train
1 NPN
transistor
(disable)
10 VDC
Yes
≤ 2.5 mA
100%
None
None
≤ 100 µA
≤ 1.2 V
≤3m
None
< 1 pulse train
Power supply AC types
Rated operational voltage
through pins A1 & A2 220
120
024
Frequency
Voltage interruption
Rated operational power
Rated impulse withstand
voltage
220
120
024
Dielectric voltage
Supply - Dupline^®
Supply - Outputs
Alternative DC supply (VDD in)
through pins 3 & 9
Reverse polarity protection
Rate operational current
Inrush current
Rated impulse withstand
voltage
Dielectric voltage
Supply - Dupline^®
Supply - Enable output
Supply - Disable output
AC types as supply source
Source voltage (VDD out)
through pins 3 & 9
Source current
Fan out
Cable length
Overvoltage cat. III (IEC 60664)
230 VAC +6%, -15% (IEC 60038)
120 VAC ± 10% (IEC 60038)
24 VAC ± 10%
45 to 65 Hz
≤ 40 ms
Typ. 2.5 VA
4 kV
2.5 kV
800 V
≥ 2 kVAC (rms)
≥ 2 kVAC (rms)
12 VDC ± 10%
Yes
≤ 20 mA
≤1A
800 V
None
≥ 2 kVAC (rms)
None
12 VDC
≤ 40 mA
≤ 4 modules .... .... 700
≤3m
Specifications are subject to change without notice (28.09.99)
1
Dupline^® is a registered trademark. A product of the CARLO GAVAZZI Group