CO1 Datasheet, PDF (1/2 Pages) List of Unclassifed Manufacturers – THROUGH HOLE CLOCK OSCILLATORS - TTL COMPATIBLE

THROUGH HOLE CLOCK OSCILLATORS - TTL COMPATIBLE
FEATURES
STANDARD 8 AND 14 PIN DIP PACKAGE
TOLERANCE AND STABILITY TO ± 25 PPM
LOW COST
AVAILABLE IN 3.3 VOLT
SERIES CO1 AND CO13
SPECIFICATIONS
SERIES
CO1
CO13
PACKAGE
14 PIN DIP
8 PIN DIP
FREQUENCY RANGE
500.00 KHz TO 125.00 MHz
500.00 KHz TO 125.00 MHz
CO1100 : ±100 ppm
CO13100 : ±100 ppm
FREQUENCY STABILITY†
CO1050 : ±50 ppm
CO13050 : ±50 ppm
CO1025 : ±25 ppm
CO13025 : ±25 ppm
OPERATING TEMPERATURE RANGE
0° C TO +70° C STANDARD
-40° C TO +85° C EXTENDED
0° C TO +70° C STANDARD
-40° C TO +85° C EXTENDED
STORAGE TEMPERATURE RANGE
-55° C TO +125° C
-55° C TO +125° C
VOLTAGE††
+5 VDC ±0.5 VDC
+5 VDC ±0.5 VDC
500.00 KHz TO 2.999 MHz: 30 mA
500.00 KHz TO 2.999 MHz: 30 mA
INPUT
CURRENT (MAX)
3.00 MHz TO 31.999 MHz: 50 mA
32.00 MHz TO 79.999 MHz: 70 mA
3.00 MHz TO 31.999 MHz: 50 mA
32.00 MHz TO 79.999 MHz: 70 mA
80.00 MHz TO 125.00 MHz: 80 mA 80.00 MHz TO 125.00 MHz: 80 mA
SYMMETRY
(AT 1.4 VDC LEVEL)
40 TO 60% NORMAL
45 TO 55% TIGHT
40 TO 60% NORMAL
45 TO 55% TIGHT
UNDER 9 MHz : ±15 ns MAX
UNDER 9 MHz : ±15 ns MAX
OUTPUT
RISE AND FALL TIME
(0.4 - 2.4 VDC)
9 MHz TO 32 MHz : ±10 ns MAX
32 MHz TO 80 MHz : ±6 ns MAX
80 MHz TO 125 MHz : ±4 ns MAX
9 MHz TO 32 MHz : ±10 ns MAX
32 MHz TO 80 MHz : ±6 ns MAX
80 MHz TO 125 MHz : ±4 ns MAX
LOGIC "0" LEVEL
+0.5 V MAX, SINK TO 16 mA
+0.5 V MAX, SINK TO 16 mA
LOGIC "1" LEVEL
+2.4 V MIN, SOURCE 0.4 mA
+2.4 V MIN, SOURCE 0.4 mA
LOAD†††
1 TO 10 TTL STANDARD
1 TO 10 TTL STANDARD
† FREQUENCY STABILITY INCLUSIVE OF ROOM TOLERANCE ,
FREQUENCY STABILITY OVER TEMPERATURE, 10% POWER SUPPLY VARIATION, AGING, SHOCK, AND VIBRATION
†† +3.3 VOLT VERSION IS AVAILABLE. CONSULT RALTRON FOR SPECIFICATIONS
††† OUTPUT LOADS ALSO AVAILABLE AT 15 pF, 30 pF AND 50 pF. CONSULT RALTRON FOR SPECIFICATIONS
ENVIRONMENTAL AND TECHNICAL CONDITIONS
OUTPUT WAVEFORM
ENVIRONMENTAL
TEMPERATURE CYCLE MIL-STD 883, METHOD 1010, 10 CYCLES -20° C TO 85° C
SHOCK
MIL-STD-202, METHOD 213, TEST CONDITION C
VIBRATION
MIL-STD-202, METHOD 204, TEST CONDITION A
RESISTANCE TO
SOLDERING HEAT
MIL-STD-202, METHOD 210, TEST CONDITION B
HUMIDITY
85% RELATIVE HUMIDITY AT 85° C 250 HOURS
MECHANICAL
GROSS LEAK TEST
MIL-STD-883, METHOD 1014, TEST CONDITION C
FINE LEAK TEST
MIL-STD-883, METHOD 1014, TEST CONDITION A
TERMINAL STRENGTH MIL-STD-202, METHOD 211, TEST CONDITION A AND C
MARKING INK
EPOXY, HEAT CURED.
MOISTURE RESISTANCE MIL-STD 202, METHOD 106, OMIT STEP 7B
SOLDERABILITY
MIL-STD-202, METHOD 208, 95% COVERAGE
SOLVENT RESISTANCE MIL-STD-202, METHOD 2002, METHOD 215
VCC
"1" LEVEL
"0" LEVEL
0 VDC
tf
tr
t
T
PART NUMBERING SYSTEM
SERIES
-
CO1 (14 PIN DIP)
CO13 (8 PIN DIP)
FREQUENCY
STABILITY
FREQUENCY
EXTENDED
TEMPERATURE
SYMMETRY
OPTIONS
100 ±100 PPM ^-
-
-
TR TAPE AND REEL
050 ±50 PPM
IN MHz
EXT
T TIGHT SYMMETRY GW GULL WING
025 ±25 PPM
3.3V +3.3 V
EXAMPLE: CO1100-20.000-EXT-T, CO13050-32.000-T-TR
35
+2.5 VDC
+1.5 VDC
+0.5 VDC
Raltron Electronics Corporation 10651 NW 19th St. Miami, Florida 33172 U.S.A.
Tel: [phone] Fax: [phone] e-mail: [e-mail] Internet: http://www.raltron.com