English
Language : 

E32D1 Datasheet, PDF (1/2 Pages) Ecliptek Corporation – OSCILLATOR
E32D1 Series
• RoHS Compliant (Pb-Free)
• PECL Output Oscillators
• 3.3V supply voltage
• Ceramic 6-pad SMD Package
• Stability to ±25ppm
• Tri-State Output
• Complementary Output
• Available on Tape and Reel
E32D1
H 2.0
L 7.0
W 5.0
OSCILLATOR
ELECTRICAL SPECIFICATIONS
Frequency Range (MHz)
Operating Temperature Range
Storage Temperature Range
Supply Voltage (VCC)
Input Current
Frequency Tolerance / Stability
Output Voltage Logic High (VOH)
Output Voltage Logic Low (VOL)
Rise Time / Fall Time
Duty Cycle
Load Drive Capability
Control Voltage (VC)
Control Voltage Range (VCR)
Frequency Deviation
Linearity
Transfer Function
Modulation Bandwidth (MBW)
Input Impedance (ZI)
Typical Phase Noise (Fo = 155.520MHz)
Logic Control/Additional Output
Tri-State Input Voltage
RMS Phase Jitter
Accumulated Period Jitter (tacc)
Period Jitter (trj)
Period Jitter (trms)
Period Jitter (tdj)
Period Jitter (tp-p)
Start Up Time
50, 51.84, 52, 52.08, 54, 57.1429, 61.44, 63.36, 65.536, 76.8, 77.76, 100, 104, 106.25, 125,
126.72, 128, 153.6, 155.52, 156.25, 159.375, 161.1328, 166.6286, 167.3315, 184.32, 186.666MHz
0°C to 70°C
-40°C to 85°C
-55°C to 125°C
With Load
3.3VDC ±5%
100mA Maximum
Inclusive of all conditions: Calibration Tolerance at 25°C, ±50ppm or ±25ppm Maximum
Frequency Stability over the Operating Temperature
Range, Supply Voltage Change, Output Load Change, 1st
Year Aging, Shock, and Vibration
20% to 80% of waveform
VCC-1.025VDC Minimum
VCC-1.620VDC Maximum
1.5 nSeconds Maximum
at 50% of waveform
50 ±10(%)
50 ±5(%)
Test Conditions for Frequency Deviation
Inclusive of Operating Temperature Range, Supply
50 Ohms into VCC-2.0VDC
1.65VDC ±1.65VDC
0.0VDC to VCC +0.5VDC
±75ppm Minimum
Voltage Change, and Output Load Change
20%, 15%, or 10% Maximum
Positive Transfer Characteristic
Measured at -3dB with Contol Voltage of +1.65VDC 10kHz Minimum
50kOhms Typical
at 10Hz Offset
-55dBc/Hz
at 100Hz Offset
-90dBc/Hz
at 1kHz Offset
-120dBc/Hz
at 10kHz Offset
-140dBc/Hz
at 100kHz Offset
-145dBc/Hz
at 1MHz Offset
-148dBc/Hz
Tri-State Enable Low / Complementary Output
VIH of 70% of VCC Minimum
No Connection
Disables Outputs: High Impedance
Enables Output
VIL of 30% of VCC Maximum
FJ = 12kHz to 20MHz
Enables Output
0.4pSec Typical, 1pSec Maximum
Sigma of Total Jitter Distribution
4pSec Typical, 5pSec Maximum
Sigma of Random Jitter
3pSec Typical, 5pSec Maximum
Sigma of Total Jitter Distribution
3pSec Typical, 5pSec Maximum
Deterministic Jitter
4pSec Typical, 10pSec Maximum
Peak to Peak of Jitter Distribution
27pSec Typical, 40pSec Maximum
10 mSeconds Maximum
MANUFACTURER
ECLIPTEK CORP.
CATEGORY
OSCILLATOR
SERIES
E32D1
PACKAGE
CERAMIC
VOLTAGE
3.3V
CLASS
OS3Y
REV.DATE
01/09
800-ECLIPTEK www.ecliptek.com for latest revision
Specifications subject to change without notice.