R3G630-AB30-63F Datasheet, PDF (1/2 Pages) ebm-papst – EC centrifugal fans

EC centrifugal fans
backward curved, single inlet, Ø 630
Highlights:
– 6-blade fan, 3-phase fan motor
– 10 VDC max. output /10 mA, 20 VDC max. output /50 mA, 0-10 V slave output, 24 V external program
input, 0-10 VDC / PWM control input, 0-10 V or 4-20 mA sensor input, external release input
– Integrated PID controller, RS485 MODBUS RTU technology
– Over-temperature protected electronics /motor, alarm relay
– Soft start, PFC passive, line undervoltage /phase failure detection
Material: Impeller: Aluminum sheet
Rotor: Coated in black
Electronic housing: Die-cast aluminum
Assembly: Galvanized steel with aluminum posts
Mounting position: Shaft horizontal or rotor on bottom; rotor on top on request
Condensate discharge holes: Rotor-side
Direction of rotation: Clockwise, seen on rotor
Nominal Data
Type
RadiPac
Motor
CFM
VAC
Hz Watts RPM
A
°C
lbs
R3G630-AB30-63F EG1R-240-630-30 M3G150-IF
10,100 200...240 50/60 2,850 1,230
7.8 -25...40 65
IP54
A
Yes
R3G630-AB21-62F EG1R-480-630-30 M3G150-IF
10,100 380...480 50/60 2,770 1,230
3.7 -25...55 65
IP54
A
Yes
(1) Nominal data at maximum load.
Curves
850
1700
16⁸⁰0⁰0
15⁷⁵0⁰0
14⁷⁰0⁰0
13⁶⁵0⁰0
12⁶⁰0⁰0
11⁵⁵0⁰0
10⁵⁰0⁰0
9⁴⁵0⁰0
8⁴⁰0⁰0
7³⁵0⁰0
630000
525000
4200
31500
2100
1500
0
Measurement: LU-132496
Air performance measured
as per: ISO 5801, Installation
category A, without protection
against accidental contact.
Suction-side noise levels: LWA as
per ISO 13347, LPA measured at
1m distance to fan axis.
The values given are valid
under the measuring conditions
mentioned and may vary accoring
to the actual installation situation.
With any deviation to the standard
set-up, the specific values have
to be checked and reviewed once
installed or fitted.
2.000
22.0.00000 4.040.0000
4.000
6.000
8.000
10.000
cfm
6.0060.000 8.0008.000 10.00010.00012.000 12.00104.000 14.01060.000 16.000 m33/h
For detailed information on the
measuring set-up, please contact
ebm-papst.
n
Pe
I
I
LwAin
A
A
rpm
W
(460V) (230V) dB(A)
AA 11 12A30 1 2052
3.0
5.6
85
AA 22 12A30 2 2593
3.7
7.0
82
AA 33 12A30 3 2770
3.7
7.8
80
AA 44 12A30 4 2581
3.7
7.0
81
AA 55 10A50 5 1237
1.8
3.4
82
AA 66 10A50 6 1569
2.2
4.3
78
AA 77 10A50 7 1779
2.5
4.8
77
AA 88 10A50 8 1558
2.2
4.3
77
AA 99 8A50 9 656
0.9
1.7
77
AA 1010 8A50 10 832
1.2
2.3
73
AA 1111 8A50 11 944
1.3
2.5
72
AA 1212 8A50 12 827
1.2
2.3
72
AA 1133 6A50 13 293
0.4
0.8
71
AA 1144 6A50 14 372
0.5
1.0
67
AA 1515 6A50 15 422
0.6
1.1
66
AA 1616 6A50 16 370
0.5
1.0
66