MCR106 Datasheet, PDF (1/3 Pages) Motorola, Inc – Silicon Controlled Rectifiers

DIGITRON SEMICONDUCTORS
MCR106 SERIES
SILICON CONTROLLED RECTIFIERS
Available Non-RoHS (standard) or RoHS compliant (add PBF suffix).
Available as “HR” (high reliability) screened per MIL-PRF-19500, JANTX level. Add “HR” suffix to base part number.
MAXIMUM RATINGS
Rating
Symbol
Value
Unit
Peak repetitive off-state voltage⁽¹⁾
(T_J = -40 to +110°C, sine wave, 50 to 60Hz, gate open)
MCR106-1
MCR106-2
MCR106-3
MCR106-4
MCR106-5
MCR106-6
MCR106-7
MCR106-8
30
60
V_DRM
100
V
V_RRM
200
300
400
500
600
On-state RMS current (180° conduction angles, T_C = 93°C)
I_T(RMS)
4.0
A
Average on-state current (180° conduction angles, T_C = 93°C)
I_T(AV)
2.55
A
Peak non-repetitive surge current
(half-cycle, sine wave, 60Hz, T_J = 110°C)
I_TSM
25
A
Circuit fusing consideration (t = 8.3ms)
I²t
2.6
A²s
Forward peak gate power (pulse width ≤ 1.0µs, T_C = 93°C)
P_GM
0.5
W
Forward average gate power (t = 8.3ms, T_C = 93°C)
P_G(AV)
0.1
W
Forward peak gate current (pulse width ≤ 1.0µs, T_C = 93°C)
I_GM
0.2
A
Peak reverse gate voltage
(pulse width ≤ 1.0µs, T_C = 93°C)
V_RGM
6.0
V
Operating junction temperature range
T_J
-40 to +110
°C
Storage temperature range
T_stg
-40 to +150
°C
Mounting torque⁽²⁾
-
6.0
In. lb.
Note 1: V_DRM and V_RRM for all types can be applied on a continuous basis. Ratings apply for zero or negative gate voltage; positive gate voltage shall not be applied concurrent
with negative potential on the anode. Blocking voltages shall not be tested with a constant current source such that the voltage ratings of the devices are exceeded.
Note 2: Torque rating applies with use of compression washer. Mounting torque in excess of 6 in. lb. does not appreciably lower case-to-sink thermal resistance. Anode lead and
heatsink contact pad are common. For soldering purposes, soldering temperatures should not exceed +200°C. For optimum results, an activated flux is recommended.
THERMAL CHARACTERISTICS
Characteristic
Thermal resistance, junction to case
Thermal resistance, junction to ambient
Lead solder temperature
(lead length ≥ 1/8” from case, 10s max)
Symbol
R_Ó¨JC
R_Ó¨JA
T_L
Maximum
3.0
75
260
Unit
°C/W
°C/W
°C
ELECTRICAL CHARACTERISTICS (T_C = 25°C, unless otherwise noted)
Characteristic
Symbol
OFF CHARACTERISTICS
Peak forward or reverse blocking current
(V_AK = Rated V_DRM or V_RRM, R_GK = 1000Ω)
T_C = 25°C
T_C = 110°C
I_DRM,
I_RRM
ON CHARACTERISTICS
Peak forward on-state voltage ⁽³⁾
(I_TM = 4.0A peak)
V_TM
Min
-
-
-
Typ
-
-
-
Max
10
200
2.0
Unit
µA
V
144 Market Street
Kenilworth NJ 07033 USA
phone +1.908.245-7200
fax +1.908.245-0555
[e-mail]
www.digitroncorp.com
Rev. 20130115