1N935 Datasheet, PDF (1/2 Pages) Compensated Deuices Incorporated – 9.0 VOLT NOMINAL ZENER VOLTAGE

DIGITRON SEMICONDUCTORS
1N935A,B-1N940A,B
MAXIMUM RATINGS
Characteristics
Junction and storage temperatures
DC power dissipation
Solder temperatures
9.0 VOLT TEMPERATURE COMPENSATED
ZENER REFERENCE DIODES
Values
-65 to +175°C
500mW @ T_L = 25°C and maximum current I_ZM of 50 mA. For optimum voltage
temperature stability, I_Z = 7.5mA (less than 75 mW in dissipated power)
260°C for 10 s (maximum)
ELECTRICAL CHARACTERISTICS
Part number
Notes 1
Zener voltage
V_Z @ I_ZT
Notes 1 & 4
Volts
Zener test
current
I_ZT
mA
Maximum
zener
impedance
Z_ZT @ I_ZT
Note 2
Ohms
Voltage
temperature
stability
UV_ZT maximum
Notes 3 & 4
mV
Temperature
range
°C
Effective
temperature
coefficient
α_VZ
%/°C
1N935
8.55-9.45
7.5
20
67
0 to +75
0.01
1N935A
8.55-9.45
7.5
20
139
-55 to +100
0.01
1N935B
8.55-9.45
7.5
20
184
-55 to +150
0.01
1N936
8.55-9.45
7.5
20
33
0 to +75
0.005
1N936A
8.55-9.45
7.5
20
69
-55 to +100
0.005
1N936B
8.55-9.45
7.5
20
92
-55 to +150
0.005
1N937
8.55-9.45
7.5
20
13
0 to +75
0.002
1N937A
8.55-9.45
7.5
20
27
-55 to +100
0.002
1N937B
8.55-9.45
7.5
20
37
-55 to +150
0.002
1N938
8.55-9.45
7.5
20
6
0 to +75
0.001
1N938A
8.55-9.45
7.5
20
13
-55 to +100
0.001
1N938B
8.55-9.45
7.5
20
18
-55 to +150
0.001
1N939
8.55-9.45
7.5
20
3
0 to +75
0.0005
1N939A
8.55-9.45
7.5
20
7
-55 to +100
0.0005
1N939B
8.55-9.45
7.5
20
9
-55 to +150
0.0005
1N940
8.55-9.45
7.5
20
1.3
0 to +75
0.0002
1N940A
8.55-9.45
7.5
20
2.7
-55 to +100
0.0002
1N940B
8.55-9.45
7.5
20
3.7
-55 to +150
0.0002
Note 1. For devices with tighter tolerances, use a nominal voltage of 9.2V and add a hyphenated suffix to the part number for desired tolerance at the end of the part number,
ie. – 2%
Note 2. Measured by superimposing 0.75mA ac rms on 7.5 mA dc @ 25°C
Note 3. The maximum allowable change observed over the entire temperature range, i.e. the diode voltage will not exceed the specified mV change at any discrete temperature
between the established limits
Note 4. Voltage measurements to be performed 15 seconds after application of dc current
MECHANICAL CHARACTERISTICS
Case
DO-35 hermetically sealed glass
Marking Body painted, alpha numeric
Polarity Cathode band
Dimensions
Inches
Millimeters
Min
Max
Min
Max
BD
-
0.107
-
2.718
BL
-
0.300
-
7.620
LD
0.018
0.022
0.457
0.559
LL
1.000
-
25.400
-
144 Market Street
Kenilworth NJ 07033 USA
phone +1.908.245-7200
fax +1.908.245-0555
[e-mail]
www.digitroncorp.com
Rev. 20120730