515-1094 Datasheet, PDF (1/1 Pages) Dialight Corporation – 3mm Round Optical Light Pipe, Bi-Level

3mm Round
® _Optopipe®
Optical Light Pipe, Bi-Level
515-1094
4.57
[.18]
3.05
[.120]
DIFFUSED
FRONT
SURAFCES;
2 PLCS
5.08
[.200]
(REF)
DIRECTION
OF LIGHT
2.77
[.109]
17.78
[.70]
(REF)
Ø 3.05± .05
[.120± .002]
TYP; 2 PLCS
9.14
[.36]
2.79
[.11]
2.29± .18
[.090± .007]
2.54
[.100]
ALIGNMENT
ONLY PIN
5.08± .07
[.200± .003]
4.39
[.173]
TYP
0.508
[.020] TYP
2.69
[.106] TYP
.99
[.039]
TYP
6.10
[.024]
3.81
[.150]
TYP
1.63
[.063]
TYP
4.27
[.168]
2.54 ±.05
[.100 ±.002]
DIRECTION
OF LIGHT
Ø 1.52±.05
[.060± .002]
TYP; 2 PLCS
BICOLORAPDS
(P/N: 597-77X1-507)
SOLDERAPD/HOLES LYAOUT
4.19
[.165]
3.35
[.132]
SINGLE COLORADPS
(P/N: 597-3XX1-507)
14.22
[.56]
7.62± .18
[.300 ± .007]
1.65
[.065]
1.63
[.064]
DIA (NOM)
MNTG PNI
5.08± .18
[.200± .007]
2.54± .18
[.100± .007]
NOTE: designed for
post-reflow
PC board insertion.
Dimensions in mm [inches]
Recommended
MicroLED SMT LEDs
for use with 515-1094
PART NO.
597-3021-5xx
597-3111-5xx
597-3211-5xx
597-3301-5xx
597-3401-5xx
597-7701-5xx
597-7721-5xx
COLOR
Red
AlGaAs Red
Orange
Green
Yellow
Red/Green
Yellow/Green
PAGE #
1-30
1-30
1-30
1-30
1-30
1-31
1-31
Features
• Can be mounted in arrays spaced .200 apart (min.)
• High transmissivity polycarbonate material
• UL94V-0 compliance
• ESD protection (circuit isolation from front panel)
• Wide viewing angle
• Arrays reduce insertion costs
• Allows bi-level SMT indicators
• Secures to PCB by press-fit
LED Data
For absolute maximum ratings and other electri-
cal and optical data on the recommended LEDs,
refer to LED data sheets.
Operating/Storage Temperature
–30°C to +100°C
Dialight Optopipe^® Light Pipe Description
This Optopipe^® is a standard design intended as a SMT compatible replacement for our 553 Series Circuit Board
Indicators. The light outputs are spaced vertically .100" from the PCB to the first element, and then 0.200" between the top
and bottom elements. We recommend a minimum of 0.200" between light pipes as a normal mounting pitch. This Optopipe^®
is held in place by 2 press-fit pins along the bottom of the device. The light pipe is not attached to the panel at any point
but can protrude through holes in the panel. The gently arcing emitting end sticks through the plastic or metal panel. The
light source is Dialight's 597 Series Type 1208 LED. The light pipe material is water clear transmissive polycarbonate rated
UL94-V0, and has a 35% oxygen index.
Dialight can provide custom Optopipe^® solutions for your applications.
Dialight Corporation • 1501 Route 34 South • Farmingdale, NJ 07727 • TEL: [phone] • FAX: [phone] •www.dialight.com