515-1070 Datasheet, PDF (1/1 Pages) Dialight Corporation – 3 x 5mm Rectangular Optopipe Optical Light Pipe, 2 Array (RJ45 Jack)

3 x 5mm Rectangular
® _Optopipe®
Optical Light Pipe, 2 Array (RJ45 Jack)
515-1070
2.54
[.100]
19.05
[.750]
13.98
[.550]
5.08
[.200]
2 PLCS
FRONT
PANEL
DIFFUSED
FRONT
SURAFCE
31.24
[1.23]
29.0
[1.142]
3.05
[.120]
1.91
[.075]
20.57
[.81] _3.56
[.140]
3.66
[.144]
C.L. LEDS
27.94
[1.100]
35.26
[1.388]
.71
[.028]
1.57
[.062]
2.01
[.079] ^.99
[.039]
1.50
[.059]
.99
[.039]
2XØ 2.87 ±.05
[.113 ±.002]
6.99
[.275]
1.35
[.053]
13.98
[.550]
C.L. MOUNTING
PIN #1
DIRECTINO
OF LIGHT
27.43
[1.080]
3.93
[.155]
7.62 ±.15
[.300 ±.006]
1.57
[.062]
NOTE: designed for
post-reflow
PC board insertion.
27.94 ±.05
[1.100 ±.002]
RECOMMENDED SOELRDPAD/HOLES LYAOUT
FOR BI-COLOR LSED
Dimensions in mm [inches]
Features
• Complements Dialight’s 515-1022 Four Array Optopipe
Light Pipe
• Allows indicators to be positioned above corresponding
RJ45 jack or D-Subminiature
• High transmissivity polycarbonate material
• UL94V-0 compliance
• ESD protection (circuit isolation from front panel)
• Wide viewing angle
• Arrays reduce insertion costs
• Secures to PCB by press-fit
Recommended
MicroLED SMT LEDs
for use with 515-1070
PART NO.
597-3001-1xx
597-3111-1xx
597-3111-5xx
597-3211-1xx
597-3211-5xx
597-3301-1xx
597-3301-5xx
597-3401-1xx
597-3401-5xx
597-7701-1xx
597-7701-5xx
597-7721-1xx
597-7721-5xx
597-7731-1xx
COLOR
Red
AlGaAs Red
AlGaAs Red
Orange
Orange
Green
Green
Yellow
Yellow
Red/Green
Red/Green
Yellow/Green
Yellow/Green
Red/Yellow
PAGE #
1-19
1-19
1-30
1-19
1-30
1-19
1-30
1-19
1-30
1-20
1-31
1-20
1-31
1-20
LED Data
For absolute maximum ratings and other electri-
cal and optical data on the recommended LEDs,
refer to LED data sheets.
Operating/Storage Temperature
–30°C to +100°C
Dialight Optopipe^® Light Pipe Description
This light pipe’s two 3 x 5mm rectangular light emitting surfaces appear bright and are optically well isolated. The light
pipe is reliably held in place by 2 press-fit pins located at either end of the light pipe array. This Optopipe^® functions as a
through-the-case indicator by conducting the light over the top of connectors or switches. A textured finish on the 2 light
emitting surfaces maximizes the viewing angle. The recommended light sources are Dialight's 597 Series PLCC-2 or
PLCC-4 Type SMT LEDs. The LEDs are mounted in a straight line on an 0.550" pitch. The light pipe material is water clear
transmissive polycarbonate rated UL94-V0, and has a 35% oxygen index.
Dialight can provide custom Optopipe^® solutions for your applications.
Dialight Corporation • 1501 Route 34 South • Farmingdale, NJ 07727 • TEL: [phone] • FAX: [phone] •www.dialight.com