KEN Datasheet, PDF (1/1 Pages) Delta Electronics, Inc. – HIGH PERFORMANCE SNAP-IN FILTERS

HIGH PERFORMANCE SNAP-IN
SERIES FILTERS
V
D E _OR
INTRODUCTIONS
1. Specially designed with ground choke providing most effective
EMI suppression for high frequency noise (ranged 5MHz-25MHz).
2. Bleeder resistor can be added with suffix "-R" on part numbers.
3. With optional Y capacitor from 100pF to 3300pF.
4. All part numbers are UL recognized, CSA certified and VDE approved.
5.Optional side snap-in mounting clip type with suffix (H) on part numbers.
for 03/06/10KENG3SA series.
COMPONENTS
PART NO.
03KENG3EA/03KENW3EA
*08KENG3EA/08KENW3EA
** 10KENG3EA/10KENW3EA
03KENG3SA/03KENW3SA
06KENG3SA/06KENW3SA
10KENG3SA/10KENW3SA
L (mH) Cx (uF) Cy (pF) Lg (uH)
3.1
0.8
0.4 0.1 2200 100
3.1
0.8
0.4
* ^{VDE approved to 6A 250V.}
** ^{UL, CSA & VDE approved to 9A 115/250 VAC.}
MINIMUM INSERTION LOSS IN dB
COMMON MODE (L-G) IN 50 OHM SYSTEM
PART NO.
FREQUENCY-MHz
.15 .50 1.0 5.0 10 30
03KENG3EA/03KENW3EA 15 20 25 40 40 45
08KENG3EA/08KENW3EA 10 15 20 35 40 50
10KENG3EA/10KENW3EA
7
12 18 30 30 50
03KENG3SA/03KENW3SA 15 20 25 40 40 40
06KENG3SA/06KENW3SA
7
15 20 35 40 40
10KENG3SA/10KENW3SA
4
12 18 30 30 45
DIFFERENTIAL MODE (L-L) IN 50 OHM SYSTEM
03KENG3EA/03KENW3EA
5
12 15 40 50 45
08KENG3EA/08KENW3EA
5
10 15 45 40 50
10KENG3EA/10KENW3EA
4
12 18 30 30 50
03KENG3SA/03KENW3SA 10 20 35 40 45 40
06KENG3SA/06KENW3SA 10 25 40 35 40 40
10KENG3SA/10KENW3SA 10 25 35 30 30 45
ELECTRICAL SCHEMATIC
L
L R Cx
I
L
N
E
N
L'
Cy
L
O
A
Cy
D
N'
G
G'
Lg
R: 1M /-R ONLY
MECHANICAL CONSTRUCTION
SPECIFICATIONS
1. Maximum leakage current each
line-to-ground @ 115VAC 60Hz: 0.20mA
@ 250VAC 50Hz: 0.40mA
2. Hipot rating (one minute)
line-to-ground: 2250VDC
line-to-line: 1450VDC
3. Operating frequency: 50/60Hz
4. Rated voltage: 115/250VAC
L
N
G
1.22 0.02
31.5 0.5
1.12MAX.
28.4MAX.
+0.012
1.12-0
+0.3
28.45-0
R0.08MAX.
R2.0MAX.
0.0315~0.063
0.8~1.6
SUGGESTED MOUNTING CUTOUT
G3SA
Suggested thickness of mounting panel is from
0.0315 (0.8) to 0.063 (1.6) inch(mm) of mounting cutout
L
N
G
1.22 0.02
31.5 0.5
1.12MAX.
28.4MAX.
+0.012
1.12-0
+0.3
28.45-0
R0.08MAX.
R2.0MAX.
0.0315~0.063
0.8~1.6
SUGGESTED MOUNTING CUTOUT
W3EA
WIRE LENGTH : 4.0" MIN.
L
N
G
1.22 0.02
31.5 0.5
G3EA
W3EA
2-12
1.12MAX.
28.4MAX.
+0.012
1.12-0
+0.3
28.45-0
R0.08MAX.
R2.0MAX.
0.0315~0.063
0.8~1.6
SUGGESTED MOUNTING CUTOUT
G3EA
UNIT: ^INCH
mm