DB2500P Datasheet, PDF (1/2 Pages) DIOTEC Electronics Corporation – 25 AMP SILICON BRIDGE RECTIFIERS

DIOTEC ELECTRONICS CORP.
18020 Hobart Blvd., Unit B
Gardena, CA 90248 U.S.A
Tel.: [phone] Fax: [phone]
Data Sheet No. BRDB-2500P-1C
ADBD-2500P-1C
25 AMP SILICON BRIDGE RECTIFIERS
FEATURES
MECHANICAL SPECIFICATION
VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM
MECHANICAL STRENGTH AND HEAT DISSIPATION
(Solder Voids: Typical < 2%, Max. < 10% of Die Area)
SERIES: DB2500P - DB2510P and ADB2504P - ADB2508P
Heat Sink
BUILT-IN STRESS RELIEF MECHANISM FOR
SUPERIOR RELIABILITY AND PERFORMANCE
BH
Heat Sink
BH
INTEGRALLY MOLDED HEAT SINK PROVIDES VERY
LOW THERMAL RESISTANCE FOR MAXIMUM HEAT
DISSIPATION
UL RECOGNIZED - FILE #E124962
MBoolddeyd
LT
HOLE FOR
D1
#8 SCREW
LL
MBoolddeyd
HOLE FOR
#8 SCREW
LD
RoHS COMPLIANT
+
D1
AC
AC
)+
D3 ^BL
)+
_
AC
BL D1
_
+
AC ^D2
MECHANICAL DATA
Case: Case: Molded epoxy with integral heat sink
Epoxy carries a U/L Flammability rating of 94V-0
Terminals: Round silver plated copper pins or fast-on terminals
Soldering: Per MIL-STD 202 Method 208 guaranteed
Polarity: Marked on side of case
Mounting Position: Any. Through hole for #8 screw.
Max. mounting torque = 20 in-lb.
Weight: Fast-on Terminals - 0.7 Ounces (20.0 Grams)
Wire Leads - 0.55 Ounces (16.0 Grams)
D2
BL
SYM
BL
BH
D1
D2
D3
LT
MILLIMETERS INCHES
MIN
28.4
9.6
15.7
17.5
13.5
n/a
MAX
28.7
10.2
16.7
18.5
14.5
15.2
MIN
1.12
0.38
0.62
0.69
0.53
n/a
MAX
1.13
0.40
0.66
0.73
0.57
0.6
Suffix "T" indicates FAST-ON TERMINALS
D1
BL
SYM
BL
BH
D1
D2
LL
LD
MILLIMETERS INCHES
MIN
28.4
9.6
17.5
10.9
20.6
1.0
MAX
28.7
10.2
18.5
11.9
n/a
1.1
MIN
1.12
0.38
0.69
0.43
0.81
0.039
MAX
1.13
0.40
0.73
0.47
n/a
0.042
Suffix "W" indicates WIRE LEADS
MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS
Ratings at 25 °C ambient temperature unless otherwise specified. Single phase, half wave, 60Hz, resistive or inductive load. For capacitive loads, derate current by 20%.
PARAMETER (TEST CONDITIONS)
Series Number
Maximum DC Blocking Voltage
Working Peak Reverse Voltage
Maximum Peak Recurrent Reverse Voltage
SYMBOL _CONTROLLED
AVALANCHE
RATINGS
NON-CONTROLLED
AVALANCHE
UNITS
VRM
ADB ADB ADB DB DB DB DB DB DB DB
2504P 2506P 2508P 2500P 2501P 2502P 2504P 2506P 2508P 2510P
VRWM
VRRM
400 600 800 50 100 200 400 600 800 1000
VOLTS
RMS Reverse Voltage
Peak Forward Surge Current. Single 60Hz Half-Sine Wave
Superimposed on Rated Load (JEDEC Method). TJ = 125^O C
Average Forward Rectified Current @ TC = 75^o C
VR (RMS)
IFSM
IO
280 420 560 35
70 140 280 420 560 700
500
AMPS
25
Junction Temperature Range
Storage Temperature Range
TJ
-55 to +150
°C
TSTG
-55 to +150
Mimimum Avalanche Voltage
Maximum Avalanche Voltage
V(BR) Min
V(BR) Max
See Note 1
See Note 1
n/a
n/a
VOLTS
Maximum Forward Voltage (Per Diode) at 12.5 Amps DC
Maximum Reverse Current at Rated VRM
@ TA = 25^o C
@TA = 125^o C
Minimum Insulation Breakdown Voltage (Circuit to Case)
VFM
IRM
VISO
1.05
1
50
2500
Typical Thermal Resistance, Junction to Case
RGJC
1.2
NOTES: (1) These bridges exhibit the avalanche characteristic at breakdown. If your application requires a specific breakdown voltage range, please contact us.
mA
VOLTS
o_C/W
3.01 25dbp
E41