35DBP Datasheet, PDF (1/2 Pages) DIOTEC Electronics Corporation – 35 AMP SILICON BRIDGE RECTIFIERS

DIOTEC ELECTRONICS CORP.
18020 Hobart Blvd., Unit B
Gardena, CA 90248 U.S.A
Tel.: [phone] Fax: [phone]
Looking for: KBPC35005, KBPC3501, KBPC3502, KBPC3504
KBPC3506, KBPC35O8, KBPC3510?
or
GBPC35005, GBPC3501, GBPC3502, GBPC3504, GBPC3506
GBPC3508, GBPC3510?
or
MDA3500, MDA3501, MDA3502, MDA3504, MDA3506,
MDA3508, MDA3510 (See Note 2)
35 AMP SILICON BRIDGE RECTIFIERS
FEATURES
MECHANICAL SPECIFICATION
VOID FREE VACUUM DIE SOLDERING FOR MAXIMUM
MECHANICAL STRENGTH AND HEAT DISSIPATION
(Solder Voids: Typical < 2%, Max. < 10% of Die Area)
SERIES: DB3500P - DB3510P and ADB3504P - ADB3508P
Heat Sink
BUILT-IN STRESS RELIEF MECHANISM FOR
SUPERIOR RELIABILITY AND PERFORMANCE
BH
Heat Sink
BH
INTEGRALLY MOLDED HEAT SINK PROVIDES VERY
LOW THERMAL RESISTANCE FOR MAXIMUM HEAT
DISSIPATION
UL RECOGNIZED - FILE #E124962
MBoolddeyd
LT
D1
HOLE FOR
#10 SCREW
(Nom. Hole Dia.=0.208")
LL
MBoolddeyd
HOLE FOR
#10 SCREW
(Nom. Hole Dia.=0.208")
LD
RoHS COMPLIANT
+
D1
AC
AC
)+
D3 ^BL
)+
_
AC
BL D1
_
+
AC ^D2
MECHANICAL DATA
Case: Case: Molded epoxy with integral heat sink
Epoxy carries a U/L Flammability rating of 94V-0
Terminals: Round silver plated copper pins or fast-on terminals
Soldering: Per MIL-STD 202 Method 208 guaranteed
Polarity: Marked on side of case
D2
BL
SYM
BL
BH
D1
MILLIMETERS INCHES
MIN
28.4
9.6
15.7
MAX
28.7
10.2
16.7
MIN
1.12
0.38
0.62
MAX
1.13
0.40
0.66
D1
BL
SYM
BL
BH
D1
MILLIMETERS INCHES
MIN
28.4
9.6
17.5
MAX
28.7
10.2
18.5
MIN
1.12
0.38
0.69
MAX
1.13
0.40
0.73
Mounting Position: Any. Through hole for #10 screw.
Max. mounting torque = 20 in-lb.
Weight: Fast-on Terminals - 0.7 Ounces (20.0 Grams)
Wire Leads - 0.55 Ounces (16.0 Grams)
D2 17.5 18.5 0.69 0.73
D3 13.5 14.5 0.53 0.57
LT
n/a 15.2 n/a 0.6
Suffix "T" indicates FAST-ON TERMINALS
D2 10.9 11.9 0.43 0.47
LL 20.6 n/a 0.81 n/a
LD 1.0 1.1 0.039 0.042
Suffix "W" indicates WIRE LEADS
MAXIMUM RATINGS & ELECTRICAL CHARACTERISTICS
Ratings at 25 °C ambient temperature unless otherwise specified. Single phase, half wave, 60Hz, resistive or inductive load. For capacitive loads, derate current by 20%.
PARAMETER (TEST CONDITIONS)
SYMBOL _CONTROLLED
AVALANCHE
RATINGS
NON-CONTROLLED
AVALANCHE
UNITS
Series Number
Maximum DC Blocking Voltage
VRM
ADB ADB ADB DB
DB DB
DB
DB
DB DB
3504P 3506P 3508P 3500P 3501P 3502P 3504P 3506P 3508P 3510P
Working Peak Reverse Voltage
Maximum Peak Recurrent Reverse Voltage
VRWM
VRRM
400 600 800 50 100 200 400 600 800 1000
VOLTS
RMS Reverse Voltage
Peak Forward Surge Current. Single 60Hz Half-Sine Wave
Superimposed on Rated Load (JEDEC Method). TJ = 125^o C
Average Forward Rectified Current @ TC = 75^o C
VR (RMS) 280 420 560 35 70 140 280 420 560 700
IFSM
IO
500
AMPS
35
Junction Temperature Range
Storage Temperature Range
TJ
-55 to +150
°C
TSTG
-55 to +150
Mimimum Avalanche Voltage
Maximum Avalanche Voltage
Maximum Forward Voltage (Per Diode) at 17.5 Amps DC
Maximum Reverse Current at Rated VRM
@ TA = 25^o C
@TA = 125^o C
Minimum Insulation Breakdown Voltage (Circuit to Case)
Typical Thermal Resistance, Junction to Case
V(BR) Min
V(BR) Max
VFM
IRM
VISO
RGJC
See Note 1
See Note 1
n/a
n/a
1.05
1
50
2500
1.2
VOLTS
mA
VOLTS
o_C/W
NOTES: (1) These bridges exhibit the avalanche characteristic at breakdown.
If your application requires a specific breakdown voltage range,
please contact us.
(2) Ensure that the mechanical configuration of the Fast-On Terminals
is suitable for your application
Data Sheet No. BRDB-3500P-1D
ABDB-3500P-1D
E45