PD10256H Datasheet, PDF (1/5 Pages) Data Delay Devices, Inc. – 8-BIT, ECL-INTERFACED PROGRAMMABLE DELAY LINE (SERIES PDU10256H)

8-BIT, ECL-INTERFACED
PROGRAMMABLE DELAY LINE
(SERIES PDU10256H)
PDU10256H
ddaeltaay ₃ ^
devices, inc.
FEATURES
• Digitally programmable in 128 delay steps
• Monotonic delay-versus-address variation
• Precise and stable delays
• Input & outputs fully 10KH-ECL interfaced & buffered
• Fits 48-pin DIP socket
PIN DESCRIPTIONS
IN Signal Input
OUT Signal Output
A0-A7 Address Bits
ENB Output Enable
VEE -5 Volts
GND Ground
PACKAGES
GND
ENB
1 48 GND
2 47 OUT
A0
VEE
GND
7 42 A1
8 41 A2
9 40 GND
A3 15 34 A4
VEE 16 33 A5
N/C
N/C
OUT
GND
ENB
N/C
N/C
N/C
GND
ENB
N/C
N/C
N/C
N/C
N/C
N/C
N/C
GND
ENB
IN
1
40
2
39
3
38
4
37
5
36
6
35
7
34
8
33
9
32
10 31
11 30
12 29
13 28
14 27
15 26
16 25
17 24
18 23
19 22
20 21
N/C
N/C
A2
A1
VEE
A0
N/C
A5
A4
VEE
A3
N/C
N/C
N/C
N/C
N/C
N/C
A7
VEE
A6
GND 17 32 GND
IN 19
PDU10256H-xxC5 SMD
PDU10256H-xxMC5 Mil SMD
PDU10256H-xx DIP
A6
VEE
23
24 25
PDU10256H-xxM Mil DIP
A7
FUNCTIONAL DESCRIPTION
The PDU10256H-series device is an 8-bit digitally programmable delay line. The delay, TD_A, from the
input pin (IN) to the output pin (OUT) depends on the address code (A7-A0) according to the following
formula:
TD_A = TD₀ + T_INC * A
where A is the address code, T_INC is the incremental delay of the device, and TD₀ is the inherent delay of
the device. The incremental delay is specified by the dash number of the device and can range from 0.5ns
through 10ns, inclusively. The enable pin (ENB) is held LOW during normal operation. When this signal is
brought HIGH, OUT is forced into a LOW state. The address is not latched and must remain asserted
during normal operation.
SERIES SPECIFICATIONS
• Total programmed delay tolerance: 5% or 2ns,
whichever is greater
Inherent delay (TD₀): 12ns typical
• Setup time and propagation delay:
Address to input setup (T_AIS): 3.6ns
Disable to output delay (T_DISO): 1.7ns typical
• Operating temperature: 0° to 70° C
• Temperature coefficient: 100PPM/°C (excludes TD₀)
• Supply voltage V_EE: -5VDC ± 5%
• Power Dissipation: 925mw typical (no load)
• Minimum pulse width: 16% of total delay
2009 Data Delay Devices
DASH NUMBER SPECIFICATIONS
Part
Number
PDU10256H-.5
PDU10256H-1
PDU10256H-2
PDU10256H-3
PDU10256H-4
PDU10256H-5
PDU10256H-6
PDU10256H-8
PDU10256H-10
Incremental Delay
Per Step (ns)
0.5 ± 0.3
1.0 ± 0.5
2.0 ± 0.5
3.0 ± 1.0
4.0 ± 1.0
5.0 ± 1.5
6.0 ± 1.5
8.0 ± 2.0
10.0 ± 2.0
Total
Delay (ns)
127.5 ± 6.4
255 ± 12.8
510 ± 25.5
765 ± 38.2
1020 ± 51.0
1275 ± 63.8
1530 ± 76.5
2040 ± 102
2550 ± 128
NOTE: Any dash number between .5 and 10
not shown is also available.
Doc #97047
DATA DELAY DEVICES, INC.
1
2/9/2009
3 Mt. Prospect Ave. Clifton, NJ 07013